11031312022 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BLOOMINGTON, IN
- Parts Used:
- W10721967
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Noise, grinding sounds. Wash tub stopped turning but motor and cycles kept functioning. Process of elimination, must be the clutch assembly.
Easy, just followed the repair video. Recommend also ordering the drive belt. Bought one locally during my repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AURORA, CO
- Parts Used:
- W11457841
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tab on door strike got broken off and washer would not operate without it.
Pushed in on door strike and rotated it counterclockwise, removed broken strike and installed new strike. NOTE: when removing the old strike (turning counterclockwise) it felt like it might break and/or was attached with an screw that I didn't see but it came right out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miranda from WEST FARGO, ND
- Parts Used:
- W11457841
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Snapped off door strike
Super easy repair, simply turn the broken door strike counterclockwise to remove; insert the new door strike into the slots and turn clockwise to lock into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delmar from EAST TROY, WI
- Parts Used:
- W11244231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
replaced drain hose that was missing
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from BROOKLYN, NY
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Making loud noises.
The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from SPRING HILL, FL
- Parts Used:
- W11457841
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The light set assembly was down to one light. So we needed to order one
The repair went really well. And it was the right part and now we can have light in our fridge.
Thank you!
Your help and fast shipping really made a difference. I will always shop for my parts with you guys. Thank you for having things no store has. It saves alit of money all around.
Thank you again.
Thank you!
Your help and fast shipping really made a difference. I will always shop for my parts with you guys. Thank you for having things no store has. It saves alit of money all around.
Thank you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from LUTHER, OK
- Parts Used:
- W11457841
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Never recieved
Ordered this part 3 times over a period of several months and never received it. Only would get emails saying it was out of stock and would be sent soon. Eventually had to but a whole new washer. Will never recomend this company or another Maytag product.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from BROWNSBORO, TX
- Parts Used:
- W11457841
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Error that Door was not closed
Using a pair of pliers turn counter clockwise to remove broken part. Install the new part by turning clockwise. Soooo easy with install time of less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from COHOES, NY
- Parts Used:
- W11481722
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Machine would stop at spin cycle
After disconnecting water lines and power, tip machine onto its back. The actuator is located under the drum. Remove the cover over the motor/ drive belt. Actuator is located by the transmission and held on by several screws. Unplug the wiring harness and remove three screws with Phillips screwdriver. Install new actuator..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from NASHUA, NH
- Parts Used:
- W11457841
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door striker prongs snapped off
The door strike part was very simple to remove. 15 seconds at most...Part ordered and delivered a day early. Install of new part was again about 15 seconds and Wala....job completed. Thanks for the great service....will call again when needed....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Wauwatosa, WI
- Parts Used:
- 285320
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
washing machine stuck on drain cycle
Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY W. from CARROLLTON, GA
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
making noise when starting spin cycle
Watch video on the site and the insulation will be easy and take about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from MILLBURY, OH
- Parts Used:
- W10752187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Worn out splines connecting transmission driveshaft to agitator.
DIY'er working on a Maytag Centennial type washing machine should be aware that replacing a a transmission or agitator due to worn out splines is only half a job done well. I originally replaced my transmission due to worn splines, only to discover later that the worn agitator splines caused the new transmission splines to wear out at an accelerated rate. Transmission and Agitator should be replaced together, along with a new Agitator mounting bolt. There are plenty of video's online of how to do this repair so I won't get into that here. Just wanted to drop the above sage advice. Transmissions for these washers aren't cheap.
Was this instruction helpful to you?
Thank you for voting!