Models
>
HLP23E
HLP23E Haier Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for HLP23E
Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
In Stock
Special Order
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Julietta
December 1, 2021
Why after final rinse and second time washing without tedergent the water not clear and with foam?
For model number HLP23E
Hello Julietta, Thank you for your inquiry. First make sure you are using the correct amount of detergent and correct type. Some washers only take a certain type of detergent. You may also have an issue with the drain hoses or drain pump. Check for any obstructions in the hoses and test the pump with a multimeter to see if it has continuity. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Common Problems and Symptoms for HLP23E
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ILANA from NEW YORK, NY
- Parts Used:
- WH23X27419
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The water stopped draining.
I emptied all the water with a cup and laid the washer down on its back on the bathroom floor, ( it is a portable), with a few small pots and rags handy to collect water, just in case.
I inspected the placement of the broken drain pump, I took photographs of all the wires placements and screws. I removed the broken drain pump pho ... Read more tographing each step, then attached the new drain pump following each step in reverse and attached the 2 colored wires to the remains of the colored wires attached to the washer. I used electric tape to isolate and cover completely the exposed wires parts i joined. I then screwed everything back in place. I put the washer upright, connected the electrical cord and did a test. It is working great, and the water is draining well! It took me over 30 minutes, as the space under the machine, where the drain pump lodges, is quite tight and I needed a flash light.
I inspected the placement of the broken drain pump, I took photographs of all the wires placements and screws. I removed the broken drain pump pho ... Read more tographing each step, then attached the new drain pump following each step in reverse and attached the 2 colored wires to the remains of the colored wires attached to the washer. I used electric tape to isolate and cover completely the exposed wires parts i joined. I then screwed everything back in place. I put the washer upright, connected the electrical cord and did a test. It is working great, and the water is draining well! It took me over 30 minutes, as the space under the machine, where the drain pump lodges, is quite tight and I needed a flash light.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GABRIEL from GANADO, AZ
- Parts Used:
- WH23X27419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Washer wouldn't drain.
Lifted up the washer from the bottom. Accessed the pump, unscrewed the motor and pulled off the rubber hose attached to the pump using a Phillips screwdriver and a wrench.
Reattached the hose and the mounting screws. Worked just fine.
Reattached the hose and the mounting screws. Worked just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annette from SEATTLE, WA
- Parts Used:
- WH13X26636
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace inlet valve
Easy. Just need to remove top and 1 panel to access. Not too tight of a workspace.
Was this instruction helpful to you?
Thank you for voting!