52270-W0 General Electric Washer - Instructions

Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on.
This was a first attempt ever at fixing an appliance and it was no big deal.

The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would need to pay a repair person to do!

I had to take most of the dryer apart because there is no rear access to the motor. It turned out to be easy to dissasembel the dryer. The only problem that I had was that I could not figure out how to route the belt around the motor and the idol pullies. I could not find anywhere that gave instructions on how to properly tension the belt. I finally figured out that the idoler pulley needs to be locked in place on the right side of the engie mount. Then the belt needs to be routed over idoler pulley and under the motor pulley. Finally release the idoler pully from the locked postion to put tension on the belt. It really turned out to be pretty easy.

Pryed off the top with a flat head screwdriver and removed the 2 screws holding the front panel to the sides. Then lifted the front panel off of the bottom brackets. Belt fit perfectly and followed the provided instructions to loop it around the motor and pulley. PartSelect got the part to me within a couple of days and the repair was a snap.

pulled old knob off. pushed new knob on.

removed front body panel (2 screws at bottom and pulled down panel), then used pliers to squeeze pinch clamps and pull back the two hoses off the pump. then removed the two pump clips that secure the pump in place and used screw driver to gently pry the old pump off the motor shaft, under that was the rubber pump slinger which was pulled off the motor shaft. The next step was to sand the rust off the motor shaft and apply some vasoline to lubricate the shaft and install the new pump slinger and pump on the motor shaft,put the pump clips back on and push the hoses on the new pump and slide the pinch clamps back into place, run test to check for leaks then re-install the front body panel.

removed upper cover, removed front cover, tested switch with digital VOM, removed and replaced!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!

fast shipping too! will recommend others!

first removed the 2 screws disconected the terminals, installed new switch connected wires back and test washer and it worked like new, i put a Jumper to get the washer to work while i got the parts. Also i received the parts in 24 hrs. Thank You.

I thought the problem was electrical so I inspected the power cord and noticed a burn on the ground connection. I disconnected the wires and inside the block was melted so I replaced it making sure the connection was tight between the power cord and block. It runs no problem. I think the dryer shorted because of a loose connection.

Received lid lock within 24 hours, fixed washer within 10 minutes...up and running. Thanks.

Happened to slam the lid by mistake and the washer started spinning. Recognized the lid lock was working haphazzardly. Also, there was a burning type odor coming from the switch. So I lifted the lid top and disconnected the switch from the lid by unscrewing 2 screws and 4 wires. When I received the new switch, I reinstalled it with 2 screws and reconnected the 4 wires.

1st - removed the two screws inside the front door panel. They are somewhat hidden up underneath so you may have to look for them. 2nd - I removed the top of the dryer cabinet by lifting it out of the clips holding it in place. 3rd - removed the two screws (one on each side) in the o=uppper corner of where the side panels connect the front panel. These are about 3/4" phillips head screws. Then the front panel could be moved to one side of the dry. 4th - remove the drum by lifting it up and out the open top area. 5th - add the new belt to the dryer tub (rib side towards the drum) and replace dryer tub to its original position. 6th - reaching in underneath the tub you need to pull the ideler pulley toward the center of the cabinet while laying the belt on the "outer side" of the ideler pulley and at the same time fitting the belt over the small pulley located on the motor. Once that is done, you reassemble in reverse order and should be good to go.

simple replacement

A few screws out of the back of the top panel, pulled the dial off. Removed two more screws and the timer assembly came off. Then I just matched the color wires one at a time to the same spots on the new assmbly.

I first ordered the replacement knob. It had broken before and I had repaired using a steel washer and epoxy to support the cracked plastic. When the support system I installed broke, I suspected a deeper problem; increased resistance to knob rotation in the control system. I removed the front panel to get back at the switch area. I wanted to lubricate the whole control, but UT seemed to be well sealed. Finding a couple areas where the plastic came together, held by a permanent metal mount, I used a pressurized silicone lubricant and sprayed into the small spaces. That allowed for easier rotation of the control, hopefully giving a longer lifespan to the new knob. DO