Models
>
WPXH214A0CC
WPXH214A0CC General Electric Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for WPXH214A0CC
Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
This assembly comes with two shocks, four nuts, one leveling leg pin and instructions. These shock absorbers keep the washer from vigorous shaking during it's cycles.
No Longer Available
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
No Longer Available
Special Order
Special Order
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
No Longer Available
On Order
In Stock
Order within the next 1 hr and 39 mins and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for WPXH214A0CC
Viewing 5 of 5Lid or door won’t close
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- STEWART from STOKESDALE, NC
- Parts Used:
- WH17X10001, WH01X10022
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Broken Spring & broken level-shock.
Disconected power & hoses. Removed 4 screws from two tabs at rear of top. Slid top fwd & up to remove. Removed two screws from lower front panel and removed panel. Removed back cover screws and back cover. Placed sling arround tub & lifted with 2"X4" on strap placing additional wood under sling supported by edges of machine. Removed one s
... Read more
cred and loosened mother that held spring hook in place. removed broken end and remainder of spring. hooked spring in hole in tub and raised spring upper hook on to support , re installed retainer. Went to lower side and removed plastic push bolts, by slipping a 1/2 " deep socker over front end and pulling from back with plirers.allign the holes in the new shock with the mount holes and nock them in place. remove sling from arround tub and re assemble all removed parts.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Hudson, WI
- Parts Used:
- WH23X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The water pump becomes very noisy
This is the second time in the same 7 year old appliance. Remove the front bottom cover by removing 2 screws. Then remove the 2 screws holding the pump down. Then unclip the electrical wire from the pump and remove both hoses from the pump by squeezing the spring clamps with a pliers. Have a pan to collect the water that will drain fr
... Read more
om the lines. Take the new pump and install it in reverse order from above.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- leslie from circleville, OH
- Parts Used:
- WH17X10001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
broken shock absorber
after pulling pins and installing new shocks, the washer still made loud ,disturbing sounds during use. Did some more investigating, turns out the inner bearings on the drum are bad. Apparently a problem with this model. Probably why the original shocks broke in the first place.
Was this instruction helpful to you?
Thank you for voting!