Models
>
GTWN7450D0WW
GTWN7450D0WW General Electric Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GTWN7450D0WW
Viewing 4 of 4
Manuals & Guides for GTWN7450D0WW
Click to downloadInstall
Installation Instructions
(0.85MB)
Manual
Owner's Manuals
(2.36MB)
Manual
Owner's Manuals
(4.19MB)
Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
In Stock
In Stock
$91.92
This is the replacement water inlet valve for your washer. It is made of mainly white plastic, with an inlet for hot and cold water, and it has three solenoids. The water inlet valve in your washer co...
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brenda
October 11, 2021
My washing machine says pause lid
For model number GTWN7450D0WW
Hello Brenda, Thank you for the question. This could indicate the Lid Lock is defective and may need to be replaced. You can try unplugging the appliance for a few mins first and restoring power to see of this resets the lock. If not the lock would need to be replaced. We hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
Common Problems and Symptoms for GTWN7450D0WW
Viewing 4 of 4Not cleaning dishes properly
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from SPRING CITY, TN
- Parts Used:
- WH02X10362
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Tub Seal Replacement - Direct Drive with Detergent/Fabric Softener Despensing
This procedure was completely different from any other Tub Seal I've done and in my opinion needs 2 people. The first thing to note is that this seal must be removed from the bottom of the outer tub. Also, the top of this machine does not hinge in back. The typical clips are in front, but the back has 2 screws that must be removed. Since
... Read more
the wiring was too involved to completely separate the top from the base, I had to improvise a stand to hold the top while the rest of the process was completed - keep slack on all remaining connected wires. The motor, clutch and bearing plate must be removed from the bottom in order to access the Tub Seal. Below are the steps I did to complete the process:
- Remove Control Panel Cover (rear)
- Disconnect as many wire harness plugs as possible from Control Board (Note positions for reassembly - pictures work well)
- Remove Pressure Switch
- Disconnect Detergent and Softener dispense hoses from Machine Top
- Rotate top 180 degrees (Flat-Spin) and position so no strain is on the still connected wires.
- Remove Tub Cover
- Remove Impeller (Agitator) from inside tub.
- Remove Tub Nut - Note Left handed Threads (I used 1/2" Drive Impact)
- Remove rear Cross Bar from cabinet (Cross Bar must be removed since tub will not fit through opening. Once removed it must be held in place or outer tub will fall)
- Remove Inner Tub - This tub is heavy and fluid-balanced. Mine required 2 people to wobble and pull for removal.
- Replace Cross bar to keep unit stable
- Lay machine on its side - use care not stretch or pull any wires.
- Remove motor, (Rotor and Stator)
- Remove Clutch and wires
- Loosen all wire ties (Use tiny screwdriver to release ties - Do Not remove the tie mount) securing wires to Bearing Plate and push wires to the outside edge of bearing Plate
- Remove all screws securing Bearing Plate to Outer Tub
- Use flat-head Screwdriver to gently pry Bearing Plate away from outer tub (Quite Heavy - Use Care)
- Tub Seal is now exposed on top of Bearing Plate and can now be removed and replaced (Be sure to clean all seal mating surfaces and lubricate with dish soap)
- Reverse this sequence in the exact order for re-assembly taking care to reconnect all wiring plugs and ground wires.
- During Re-assembly I used Blue Loctite on all bolts securing the Clutch, Stator, and Rotor as I found several very loose on my machine
- Remove Control Panel Cover (rear)
- Disconnect as many wire harness plugs as possible from Control Board (Note positions for reassembly - pictures work well)
- Remove Pressure Switch
- Disconnect Detergent and Softener dispense hoses from Machine Top
- Rotate top 180 degrees (Flat-Spin) and position so no strain is on the still connected wires.
- Remove Tub Cover
- Remove Impeller (Agitator) from inside tub.
- Remove Tub Nut - Note Left handed Threads (I used 1/2" Drive Impact)
- Remove rear Cross Bar from cabinet (Cross Bar must be removed since tub will not fit through opening. Once removed it must be held in place or outer tub will fall)
- Remove Inner Tub - This tub is heavy and fluid-balanced. Mine required 2 people to wobble and pull for removal.
- Replace Cross bar to keep unit stable
- Lay machine on its side - use care not stretch or pull any wires.
- Remove motor, (Rotor and Stator)
- Remove Clutch and wires
- Loosen all wire ties (Use tiny screwdriver to release ties - Do Not remove the tie mount) securing wires to Bearing Plate and push wires to the outside edge of bearing Plate
- Remove all screws securing Bearing Plate to Outer Tub
- Use flat-head Screwdriver to gently pry Bearing Plate away from outer tub (Quite Heavy - Use Care)
- Tub Seal is now exposed on top of Bearing Plate and can now be removed and replaced (Be sure to clean all seal mating surfaces and lubricate with dish soap)
- Reverse this sequence in the exact order for re-assembly taking care to reconnect all wiring plugs and ground wires.
- During Re-assembly I used Blue Loctite on all bolts securing the Clutch, Stator, and Rotor as I found several very loose on my machine
Read less
Was this instruction helpful to you?
Thank you for voting!