GMAN1200D0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Miguel from Jacksonville, FL
- Parts Used:
- WH13X10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The washer stop and blinks in the RINSE MODE
I called a repair person to check my 15 months old GE front loader washer that stopped in rinse mode. After his inspection he said it was a deffected computer board and it would be very expensive to replace the 3 computers boards inside and it would be cheaper to buy a new top loader washer. The next day I lifted the top cover and found a taped plastic envelope with instructions titled “For service Technicians Only." On page 2, instruction on to how to enter the washer in to service mode and to test the washer:
Press : Signal, Delay, Signal, Delay (within 30 seconds of plug in washer)
Then rotate main knob to #102 and press Start:(the washer did a test for finding the problem) , and for me was : E22 , it means : replace solenoid valve assembly.
So I order the part from Partselect.com for $58.00 and my Washer runs beautiful, thanks to the instructions inside.
Press : Signal, Delay, Signal, Delay (within 30 seconds of plug in washer)
Then rotate main knob to #102 and press Start:(the washer did a test for finding the problem) , and for me was : E22 , it means : replace solenoid valve assembly.
So I order the part from Partselect.com for $58.00 and my Washer runs beautiful, thanks to the instructions inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dallas, PA
- Parts Used:
- WH10X10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
"Door Locked" light always on. Washer would not run
Remove bottom kick plate of washer. Remove 4 screws behind door that hold the latch/lock assembly. Reach up inside the washer from underneath to unplug 3 wire connectors. (This is a very tight spot). Once wires are off, part comes right out. Connect wires to the new part - this is by far the most difficult part of the job because it is way up inside the washer. Replace all bolts.
Overall, pretty easy to do - just reconnecting the wires is a pain, but if you are patient it is not a big deal.
Overall, pretty easy to do - just reconnecting the wires is a pain, but if you are patient it is not a big deal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felipe from Houston, TX
- Parts Used:
- WH13X10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stops at rise
removed 5 screws, unscrew two more screws, remove the houses and disconnect the wires remove the watter valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Spring Branch, TX
- Parts Used:
- WH01X10356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door plunger broken so could not lock.
Part came quickly, was exactly what I needed, 2 minutes later, washing clothes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from HARRIMAN, TN
- Parts Used:
- WH11X34740
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer stopped during wash cycle and wouldn't open.
Removed three 7mm sheet metal screws from the bottom front panel.
The drain pump is in the front right.
Removed the manual drain screen to drain residual water from the system. A bucket was necessary to collect all the water.
Disconnected the inlet and outlet hose.
Disconnected the electric supply.
Removed two Phillips screws holding the pump to the bottom of the machine.
Slid the pump towards the rear to clear the support pegs and removed it from the front opening.
Installation is the reverse of those steps.
The drain pump is in the front right.
Removed the manual drain screen to drain residual water from the system. A bucket was necessary to collect all the water.
Disconnected the inlet and outlet hose.
Disconnected the electric supply.
Removed two Phillips screws holding the pump to the bottom of the machine.
Slid the pump towards the rear to clear the support pegs and removed it from the front opening.
Installation is the reverse of those steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from BOULDER, CO
- Parts Used:
- WH10X10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Latch Failure Code
Unplug machine.
Remove band from front bellows by prying the spring at 6:00 o:clock loose.
Pull back bellows on right side.
Remove 3 torx screws and gently pull door each lock assembly out. Unplug 3 wire harness connectors and plug into new latch lock in same order.
Screw new latch lock in place and replace bellows and band.
Done
Remove band from front bellows by prying the spring at 6:00 o:clock loose.
Pull back bellows on right side.
Remove 3 torx screws and gently pull door each lock assembly out. Unplug 3 wire harness connectors and plug into new latch lock in same order.
Screw new latch lock in place and replace bellows and band.
Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from MINNEAPOLIS, MN
- Parts Used:
- WH13X10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
washer would stop at certain points in cycle
Replace the water valve according to the youtube video from this site. It was really easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from SURF CITY, NC
- Parts Used:
- WH11X34740
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water not spinning out. Laundry still real wet, washer would not turn off, just Pause\Start button blinking.
Pulled off the front. Had to feel around to find how pump was attached. Detached it and popped in new one. Would be better if there was more visibility in area.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herman from SAN DIEGO, CA
- Parts Used:
- WH11X34741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water leaking
Did not have to use the new pump filter. The old one finally worked. I probably didn’t screw it in tight enough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Orville from GREEN CV SPGS, FL
- Parts Used:
- WH11X34740
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Stopped at 10 minutes and wouldn't spin/drain water.
Removed top of washer. Three screws.
Removed control panel. Three screws.
Removed spring loaded ring which seals washer rubber gasket and door assembly. Disconnect door interlock connectors.
Removed front panel which includes door assembly. Three screws.
Access to pump is on lower shelf. Remove connectors from pump assembly. Remove clamps on two pump inlet/outlet hoses. Remove two screws holding pump assembly.
Install new pump assembly in reverse,
Removed control panel. Three screws.
Removed spring loaded ring which seals washer rubber gasket and door assembly. Disconnect door interlock connectors.
Removed front panel which includes door assembly. Three screws.
Access to pump is on lower shelf. Remove connectors from pump assembly. Remove clamps on two pump inlet/outlet hoses. Remove two screws holding pump assembly.
Install new pump assembly in reverse,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josefa m from PANORAMA CITY, CA
- Parts Used:
- WH11X34740
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The washer drain pump wasn't working properly
Was so easy to replace the part first take out the lower front cover and then couple screws and also two clamps then assembly back on the same order tested and finished
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolann from MOSCOW, TN
- Parts Used:
- WH11X34740
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Drain pump replacement
utube video made this repair very easy! remove front lower cover, drain pump will be on the right, 2 screws hold pump in place (unscrew), remove hoses by using plyers to slap hoses off pump, remove old pump. replace with new one, screw back in, replace hose & claps. DONE!! i ran a rinse and drain cycle before replacing the front cover just to be sure there were no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Griswold, CT
- Parts Used:
- WH01X10356
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Door Plunger Broke
The white door plunger broke after 3 years of use. After replacing the door plunger the door still would not close. so I also ordered the door lock part for inside the washer. This was also an easy replacement but far more expensive. A thing to note. If the door plunger breaks you may need to reset you locking piece. and save your self 130 dollars. To do this. remove the top panel of the washer. remove the control panel. remove the spring ring around the rubber seal. disconnect the door locking piece and remove from washer. now use a hook or stiff wire and loop inside the door plunger hole and pull the lock out. if it wont release ensure the white piece on the bottom is lowered all the way. This is also possible to reset with out removing but you wont be able to check the white piece(the lock holder). What ever you do do not take apart the locking piece it has lots of little parts an will give you nightmares.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Los Angeles, CA
- Parts Used:
- WH13X10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Washer keeps Pausing.
After getting error message from washer, Looked it up and found if the water lines are find, then replace the water valve. After replacing the valve, everything works fine.
Was this instruction helpful to you?
Thank you for voting!