GFWS2605F0MC General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from LYONS, CO
- Parts Used:
- WH23X10051
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Drain pump failed
Remove back cover and with a light and a mirror the screws can be identified. Three hold this pump on. Remove electrical connection then the pump. So also remove the corrugated connecting boot by undoing three clamps. Clean and reassemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WELDON, IL
- Parts Used:
- WH08X22620
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Riper gasket main, needed replaced.
After trying multiple times, multiple ways to stretch the gasket over the washer drum with no luck, I was able to get it installed but it took 2 more people. 4 hands to hold the gasket while the other person fits it around the drum. I noticed in the install videos they start the process then cut away, and magically the gasket is installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Miami, FL
- Parts Used:
- WH01X10727
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
Washer was vibrating during spin cycle
Problem got worse the technician installed the damper assembly but the problem got worse . The machine sounds like a tractor .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CONCORD TWP, OH
- Parts Used:
- WH12X26034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Power spike caused the control not activate motor on drum.
I downloaded a service manual for $9.95 online that lead me step by step to the board.I order the board from another supplier but it was back ordered for 4 to 6 weeks. Was lucky to find Partselect. They had the part in stock with fast shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from NEW BALTIMORE, MI
- Parts Used:
- WH45X10137
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set
Water leakage, inner basket bearing play, motor not running
Replaced outer drum, both halves, inner basket/trunnion assy. , Fan housing from excessive vibration/broken mount tabs. Used multimeter to test rotor position sensor ohms, replaced sensor, machine operating as new now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from OWASSO, OK
- Parts Used:
- WH12X26034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Power surge. No display
Replaced smoked Electronic Control Board, powered up and ran diagnostics. Machine powered up just fine but would fail the drum speed test. Replaced the RPS Module and machine works like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Regis from SAN MARTIN, CA
- Parts Used:
- WH45X10138
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
TUB OUT OF BALANCE
Replaced the balance ring on the tub but the main tub was cracked and could not be repaired.
Parts select was very helpful. Sent me instructions to repair the washer and replaced defective parts from shipping within 2 days. VERY GOOD EXPERIENCE
Parts select was very helpful. Sent me instructions to repair the washer and replaced defective parts from shipping within 2 days. VERY GOOD EXPERIENCE
Was this instruction helpful to you?
Thank you for voting!