Models
>
GFWH2405L0MG
GFWH2405L0MG General Electric Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GFWH2405L0MG
Viewing 4 of 4Manuals & Guides for GFWH2405L0MG
Click to downloadKeep searches simple, eg. "belt" or "pump".
$102.75
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
In Stock
In Stock
This part is the replacement door plunger or door strike for your washer. It is made of white plastic and is approximately 2 inches by 1.5 inches. The door strike attaches to the washer door and activ...
No Longer Available
In Stock
In Stock
In Stock
In Stock
On Order
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for GFWH2405L0MG
Viewing 4 of 4Leaking
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Altoona, PA
- Parts Used:
- WH13X10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
machine would not fill on any cycle requiring hot water, Machine would work fine on cold cycles
I Disconnected power to machine and shut off water supply lines. Move washer away from wall and removed supply lines.(good time to replace them if older than five years) Where these supply lines attach to the washer is the water valve you are replacing. There are 3 screws on the back of the cabinet lid, then on the front 3 more screws hol
... Read more
d the lid to the plastic control housing. After removing screws you need to slide the lid up and towards the back of the machine app. 1 1/2"to 2" before you can raise the lid up and off of the machine. Once the lid is off it is just one screw holding the valve, and a hose clamp that needs removed from the end of the valve. Then slide valve to the right (looking from front of machine to the back.) I left the wires attached to the old valve,installed the new valve then reattached the wires in the same order as they were on the old valve to avoid confusion. (note valve must slide into place to get screw to line up.)assemble is reverse of the above steps. Don't forget to level machine. Be careful attaching water supply lines plastic valve threads can strip without much effort.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Tucson, AZ
- Parts Used:
- WH13X10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
inlets cross threaded from water hose connections
I unplugged the power cord from the wall outlet, then I had to remove the top panel off the machine by removing the three phillips screws holding the back trim strip to the front top of the machine, than I removed the three 1/4 inch head screws holding the top panel found at the back top of machine. I now pulled the top pannel to the rear
... Read more
and removed the top pannel. Then I used pliers to squeeze open and slide clear the small clamp to the rubber hose to the valve and removed the hose end to the valve. Then I carefully pulled off the four wire connectors to the two solenoids of the valve.
Than I removed the one 1/4 inch head screw found on the back side of the machine securing the valve to the machine. Then I removed the valve by sliding it to the mounting screw side to disengage it.
Install the valve in reverse order but I tightened the valve holding screw only till it's seated because it screws into soft plastic. 6/15/08
Than I removed the one 1/4 inch head screw found on the back side of the machine securing the valve to the machine. Then I removed the valve by sliding it to the mounting screw side to disengage it.
Install the valve in reverse order but I tightened the valve holding screw only till it's seated because it screws into soft plastic. 6/15/08
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dallas, PA
- Parts Used:
- WH10X10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
"Door Locked" light always on. Washer would not run
Remove bottom kick plate of washer. Remove 4 screws behind door that hold the latch/lock assembly. Reach up inside the washer from underneath to unplug 3 wire connectors. (This is a very tight spot). Once wires are off, part comes right out. Connect wires to the new part - this is by far the most difficult part of the job because it
... Read more
is way up inside the washer. Replace all bolts.
Overall, pretty easy to do - just reconnecting the wires is a pain, but if you are patient it is not a big deal.
Overall, pretty easy to do - just reconnecting the wires is a pain, but if you are patient it is not a big deal.
Read less
Was this instruction helpful to you?
Thank you for voting!