Models
>
GFW400SCM0WW
GFW400SCM0WW General Electric Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GFW400SCM0WW
Viewing 4 of 4
Keep searches simple, eg. "belt" or "pump".
This is the replacement water valve for your washer. It has 2 inlets and 3 outlets. The water valve connects to the water source and solenoid wires, and ensures the tub has the right amount of water e...
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
$285.07
This part is also called the Door Boot Seal. It's the main seal between the front bulkhead and the outer tub.
In Stock
In Stock
In Stock
On Order
In Stock
$131.37
The door lock prevents the washer door from opening during the wash cycle or spin cycle.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for GFW400SCM0WW
Viewing 3 of 3Leaking
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Miguel from Jacksonville, FL
- Parts Used:
- WH13X10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The washer stop and blinks in the RINSE MODE
I called a repair person to check my 15 months old GE front loader washer that stopped in rinse mode. After his inspection he said it was a deffected computer board and it would be very expensive to replace the 3 computers boards inside and it would be cheaper to buy a new top loader washer. The next day I lifted the top cover and foun
... Read more
d a taped plastic envelope with instructions titled “For service Technicians Only." On page 2, instruction on to how to enter the washer in to service mode and to test the washer:
Press : Signal, Delay, Signal, Delay (within 30 seconds of plug in washer)
Then rotate main knob to #102 and press Start:(the washer did a test for finding the problem) , and for me was : E22 , it means : replace solenoid valve assembly.
So I order the part from Partselect.com for $58.00 and my Washer runs beautiful, thanks to the instructions inside.
Press : Signal, Delay, Signal, Delay (within 30 seconds of plug in washer)
Then rotate main knob to #102 and press Start:(the washer did a test for finding the problem) , and for me was : E22 , it means : replace solenoid valve assembly.
So I order the part from Partselect.com for $58.00 and my Washer runs beautiful, thanks to the instructions inside.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felipe from Houston, TX
- Parts Used:
- WH13X10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stops at rise
removed 5 screws, unscrew two more screws, remove the houses and disconnect the wires remove the watter valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from HARRIMAN, TN
- Parts Used:
- WH11X34740
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer stopped during wash cycle and wouldn't open.
Removed three 7mm sheet metal screws from the bottom front panel.
The drain pump is in the front right.
Removed the manual drain screen to drain residual water from the system. A bucket was necessary to collect all the water.
Disconnected the inlet and outlet hose.
Disconnected the electric supply.
Removed two Phi ... Read more llips screws holding the pump to the bottom of the machine.
Slid the pump towards the rear to clear the support pegs and removed it from the front opening.
Installation is the reverse of those steps.
The drain pump is in the front right.
Removed the manual drain screen to drain residual water from the system. A bucket was necessary to collect all the water.
Disconnected the inlet and outlet hose.
Disconnected the electric supply.
Removed two Phi ... Read more llips screws holding the pump to the bottom of the machine.
Slid the pump towards the rear to clear the support pegs and removed it from the front opening.
Installation is the reverse of those steps.
Read less
Was this instruction helpful to you?
Thank you for voting!