Models
>
WA4900ADD3
WA4900ADD3 Frigidaire Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for WA4900ADD3
Viewing 5 of 5Keep searches simple, eg. "belt" or "pump".
In Stock
This screw-in plastic leveling leg supports the washing machine. If your washer loses balance while it is tumbling, or makes loud noises, then it is best to replace the leveling leg to make sure the h...
In Stock
$74.78
This seal helps prevent any leaking around the transmission of washing machines.
In Stock
$11.21
This screw is designed to fit washers and dryers. Refer to the diagram provided by the manufacturer for further installation instructions and accurate application of screw in your tool.
In Stock
Mounting bracket on this part replaces old style ( You may need to drill off old bracket before mounting new lock).
No Longer Available
In Stock
In Stock
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for WA4900ADD3
Viewing 7 of 7Leaking
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- alvaro from east hampton, NY
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and remo
... Read more
ved the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenessa from Tacoma, WA
- Parts Used:
- 134101800
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lid Lock Assembly broke
The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would
... Read more
need to pay a repair person to do!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Somerville, MA
- Parts Used:
- 134418700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Agitator Drive Block wore out
Removed fastening screw and Agitator. Removed and replaced Agitator Drive Block. Replaced and fastened Agitator. Done in 5 min.
Ordered part around noon. Shipping was 3-5 days. Part arrived in LESS than 24 hours.
Very happy camper here!
Ordered part around noon. Shipping was 3-5 days. Part arrived in LESS than 24 hours.
Very happy camper here!
Was this instruction helpful to you?
Thank you for voting!