FWS223RFS2 Frigidaire Washer - Instructions

carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.

uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes like new spins and drains all water from tub.

After reading the possiblilities of problem, I determined that the drain pump was not working; therefore I ordered a new one. When I opened the washer to replace the part, I found out that the pump was working but the filter was stuffed with pieces of rubber that came out from a rug I washed. Once all the stuff was removed, the washer worked just fine. PartSelect was very gracious to accept the returned with not questions asked!! Thanks partSelect.

First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.

The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would need to pay a repair person to do!

Disconnect water and electricity.
Shop-vac out the water in the internal drain hose.
Remove back cover, tip washer on side to gain access.
Un-clamp rubber drain hose,unscrew pump and remove.
Cleanout filter cup (yuk!) find coins and hairpins.
Attach drain hose to new pump and re-install with hose clamps from hardware store because spring clamps were impossible (arthritis in fingers).
Reconnect water and electricity.
Test for leaks and tighten clamps if necessary.

The problem with my very old washer was that the tension spring had broken long ago and I had jerry-rigged it in place with a cable tie. It would work, but you had to give the drum a spin by hand when it hit the spin the cycle. This probelm further caused the premature wearing of the drive belt, due to slippage. I ordered both a new spring and a new belt. Upon their arrival, I removed the two screws holding the front panel and lowered it off and out of the way. The old, worn belt was very easy to remove, as there was very little tension on it. Next I attempted to remove the washer that holds the idle arm on. It is in a very awkward spot, and it appears the the washing machine is sort of built around it. I bent it gradually with locking pliers until I could force it off with the blade of a flat screwdriver. Then the idler arm was easy to lower of its axle by twisting the drum a bit and pulling it to one side. I put the new spring into the idler arm, making sure the plastic bushing was in place and replaced the arm. I then repositioned to belt and replaced the front panel. It works great now.

Removed fastening screw and Agitator. Removed and replaced Agitator Drive Block. Replaced and fastened Agitator. Done in 5 min.

Ordered part around noon. Shipping was 3-5 days. Part arrived in LESS than 24 hours.

Very happy camper here!

pulled old knob off. pushed new knob on.

Unplugged machine.
Turned off water supply.

Removed front panel.
Pushed in on belt tensioner, removed old belt, replaced with new belt.

Used pry bar to lift the base assembly high enough off the snubber to remove it. Partially propped it with 2x4 wood scraps.

Used bent clothes hangar to remove old snubber ring, to protect my hands.

Replaced snubber, arrow pointing up.
Carefully lowered base assembly.

Replaced front panel.
Turned water back on, plugged back in, washing machine no longer 'walks'.

Remember to check the washer against a level if you moved the machine.

removed upper cover, removed front cover, tested switch with digital VOM, removed and replaced!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!

fast shipping too! will recommend others!

This is the third time I have ordered parts from this company .I can't say enough good things about them from their fast shipping( always arrives sooner than they state)To the quality of the parts and the shipping packages.A first class operation from start to finnish.First step was to disconect power supply.Second was to remove washer drain hose from house drain.Third remove two (2) phillips head screws from front cover of washer ,located at bottom right and left side of front panel near floor.Lift front panel up to unhook metal retainers on panel that connect it to washer side panels.Use pliers to remove spring clamp from hose. Remove hose from washer pump. Remove clamp from hose,remove plastic retainer holding hose to washer bottom.Feed hose out the back of the washer through washer drain hose hole in the back pannel of the washer.Remove plastic retainer.Insert the new hose through the hole in the back pannel install the hose clamp and install the hose back on the pump.Relocate clamp on hose, take front panel,lift into place,push down to lock retaining taps into side cover slots replace the two phillips head screws.

After removing the front of the washer, I used slip joint pliers for the hose clamps, then a screwdriver for the mount bolts and replaced the pump motor in reverse order. The pump was ordered on line on a Friday before 10am and was delivered on saturday moring by FedEx. I could not have expected such fast and efficent service!
Great Job!!

It turned out that the pump was fine. There is a filter within the rubber bellows between the washer drum and the motor. You need to remove the entire bellows to get to it. Just remove the motor and you can un-clip the hose tensioners. They are exactly like the ones you would fine on most foreign cars - just compress with pliers and move back on the hose. Clean out the plastic filter. A small nail had worked its way through the plastic filter and lodged in the motor impeller. Removing this nail and reassembling, it all worked as new! I kept the pump and motor as a future spare rather than return it.

remove side panel & start rinse cycle & heard a grinding noise in discharge pump. used a bucket to catch water upon removeal of discharge hose to pump. unplug disconnect plug to motor, remove pump from unit. Discovered propeller was loose in housing. Googled Partselect.com, odered part & in 2 days later installed new pump on unit. Started a load of wash & it has been working perfect ever since. thanks to PartSelect.com for the service, the repair was minimal & easy for the DO IT YOURSELFER. Bill Starry