FFT6009 Frigidaire Washer - Instructions

carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.

First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.

The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would need to pay a repair person to do!

removed front body panel (2 screws at bottom and pulled down panel), then used pliers to squeeze pinch clamps and pull back the two hoses off the pump. then removed the two pump clips that secure the pump in place and used screw driver to gently pry the old pump off the motor shaft, under that was the rubber pump slinger which was pulled off the motor shaft. The next step was to sand the rust off the motor shaft and apply some vasoline to lubricate the shaft and install the new pump slinger and pump on the motor shaft,put the pump clips back on and push the hoses on the new pump and slide the pinch clamps back into place, run test to check for leaks then re-install the front body panel.

removed upper cover, removed front cover, tested switch with digital VOM, removed and replaced!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!

fast shipping too! will recommend others!

first removed the 2 screws disconected the terminals, installed new switch connected wires back and test washer and it worked like new, i put a Jumper to get the washer to work while i got the parts. Also i received the parts in 24 hrs. Thank You.

i took out the two back screws lift the top.
took the two bottom front screws , lifted andtook off the front panel.took off the old belt an intall the new one in a circular motion put the panel and top back on and done.

Removed 2 screws at bottom of the front panel - removed front panel by sliding the panel down about 1/2 inch and then away from the appliance- v belt is removed by pushing the tensioner pulley to remove tension from the belt and turning the pulley untill the belt is removed instalation is a simple reverse of the process. I did't have a repair manual so every step was trial and error untill I was able to complete the repair.

Received lid lock within 24 hours, fixed washer within 10 minutes...up and running. Thanks.

I got online and figured out exactly how to take off the front of the washer and then how to replace the belt. It was so easy. The part itself arrived much sooner than predicted. It fit perfectly and my washing machine is now running smoothly and quietly.

Checked problem on-line and discovered it was the water inlet valve. Matched the part on part select. Com. Finding the part was very easy. Part select had a grid behind the picture to help determine the size and pictures from all sides. Removing the old part, matching it, and replacement took a total of 30 minutes. I now have clean clothes.

After moving machine to an area that allowed easy access to the unit, disconnected the water supply hoses from the inlet valve.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, disconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.

Happened to slam the lid by mistake and the washer started spinning. Recognized the lid lock was working haphazzardly. Also, there was a burning type odor coming from the switch. So I lifted the lid top and disconnected the switch from the lid by unscrewing 2 screws and 4 wires. When I received the new switch, I reinstalled it with 2 screws and reconnected the 4 wires.

Removed the 2 screws that hold the front panel on and slid the panel down to remove it, after first lifting the top panel and supporting it in the upright position out of the way. popped the two clips that hold the pump on, and used the pliers to remove the hose clamps on the pump. the pump was rusted to the motor shaft, so I had to use some force to pry it off of the motor. then i had to use some sandpaper to clean the rust off of the motor shaft. slid the new pump on and secured the hoses and hold down clips. then pushed the belt tensioner in and replaced the belt. the machine is like new again.

followed the instructions on a blog