EWFLS70JSS0 Electrolux Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michelle from Loves Park, IL
- Parts Used:
- 134616100
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Original bellow had 2 largish holes in the upper left quadrant; random leaking.
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfectly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from DAYTON, OH
- Parts Used:
- 134937300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Broken door latch
First, I went to the PartSelect website and easily found the part at a reasonable price. I ordered it early on a Wednesday afternoon, and gladly spent the extra $25 to ship it overnight. That evening, PartSelect sent me an email stating that the part had shipped that very day, and - mistakenly - I took that literally. FedEx tracking predicted that the part would arrive on Friday, July 5, which made sense because the 4th was a holiday.
But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July.
That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping.
Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes.
But no thanks to PartSelect.
But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July.
That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping.
Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes.
But no thanks to PartSelect.
Was this instruction helpful to you?
Thank you for voting!
Electrolux Upright Washer Door Wouldn't Open
Parts took twice as long to arrive shipped from Utah to Houston, Texas. Once arrived parts were straight forward to install.
1) Open the door by tripping the door strike using yard trimmer line.
2) Turned Power off (unplugged unit)
3) Used needle noses pliers to remove door rubber boot retainer
4) Folded right-side of rubber in to removed switch assembly
5) Used Phillips screwdriver to remove switch assembly screws, navigated damaged switch part forward then disconnected line.
6) Connected new switch to line, navigate part back into washer and screwed back in.
7) Repositioned door rubber boot and reattached door boot retainer wire with hands and needle noose pliers.
8) Replaced door strike using Phillips screw driver.
9) Re-plugged washer power to outlet, closed door and ran a test cycle. All good!
1) Open the door by tripping the door strike using yard trimmer line.
2) Turned Power off (unplugged unit)
3) Used needle noses pliers to remove door rubber boot retainer
4) Folded right-side of rubber in to removed switch assembly
5) Used Phillips screwdriver to remove switch assembly screws, navigated damaged switch part forward then disconnected line.
6) Connected new switch to line, navigate part back into washer and screwed back in.
7) Repositioned door rubber boot and reattached door boot retainer wire with hands and needle noose pliers.
8) Replaced door strike using Phillips screw driver.
9) Re-plugged washer power to outlet, closed door and ran a test cycle. All good!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BONNEY LAKE, WA
- Parts Used:
- 134937300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stricken broke pot metal.
R and r
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from JACKSONVILLE, FL
- Parts Used:
- 134616100
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
ELECTRONIC COMPONENT
Still waiting on the part. It apparently is on back order and I'm still waiting to get the part to try and repair the dryer.
I estimate an hour to replace the part if I ever get the part.
I estimate an hour to replace the part if I ever get the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from PONTE VEDRA, FL
- Parts Used:
- 134937300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The door strike was broken not allowing the door to close. Replacing it was easy however a big lesson learned. I failed to think that the electromagnetic latch located on the washer that the strike goes in to was also broke. After ordering the electrical latch assembly all worked as planned.
All that was needed was a Phillips screw driver. Getting the door latch assembly out was a bit more effort then the door striker. You have to remove the chrome ring around the door opening first. Requires backing out screw on lower left part of the chrome ring to remove
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Baruch from HURLEYVILLE, NY
- Parts Used:
- 134618213
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
washer stops in middle of cycle and E53 appears on the screen
1 you have to order a new motor control board
2 unscrew the back panel
3 unscrew the top panel
4 unscrew the bracket
5disconnect the old motor control board
6 connect the new motor control board
2 unscrew the back panel
3 unscrew the top panel
4 unscrew the bracket
5disconnect the old motor control board
6 connect the new motor control board
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from FREDERICA, DE
- Parts Used:
- 134937300
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door latch broke
Replaced the door latch. Don't pay for overnight or 2 day delivery it will not get there. Paid for 2 day it arrive a week later. They will not refund the postage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from ROCKLAND, ME
- Parts Used:
- 134629900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door to washing machine would not close properly
I replaced the thingy and the whatsit, turned the machine off, then on, and the door worked properly thereafter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marguerite from Oconomowoc, WI
- Parts Used:
- 134937300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken strike
amazing 2 screws out part out part in 2 screws in done 2 minutes thank you for such a easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from DELTONA, FL
- Parts Used:
- 134618213
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
While using washer a E9F code appeared and stopped working.contacted parts select trouble shooting site they told me what it was ordered the part they were right on!back washing again thanks so much for the help!
Did it with no problems at all just followed the video step by step worked great done in 1hour!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donna from gardnerville, NV
- Parts Used:
- 134762010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
not cycling
put new part did reset on main controles
Was this instruction helpful to you?
Thank you for voting!