Models
>
EIFLW55HMB0
EIFLW55HMB0 Electrolux Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for EIFLW55HMB0
Viewing 5 of 5Manuals & Guides for EIFLW55HMB0
Click to downloadInstall
Installation Instructions
(12.77MB)
Manual
Owner's Manuals
(18.30MB)
Manual
Owner's Manuals
(1.98MB)
Specs
Product Specifications Sheet
(0.23MB)
Wiring
Wiring Diagram
(0.23MB)
Keep searches simple, eg. "belt" or "pump".
$11.22
This screw is designed to fit washers and dryers. Refer to the diagram provided by the manufacturer for further installation instructions and accurate application of screw in your tool.
In Stock
In Stock
$11.76
This is a screw and it is used with a variety of home appliances. It is less than 1/2 an inch long, and is #8-18 x 3/8. This part is a pan head, sheet metal, screw. It is made of metal.
In Stock
In Stock
In Stock
$9.27
This part is the replacement screw for your washer. The head is approximately inch in diameter and the screw is approximately 3/4 inch in length. It is made of metal and is sold individually. This is...
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
On Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for EIFLW55HMB0
Viewing 3 of 3Lid or door won’t close
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Locking Issues
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michelle from Loves Park, IL
- Parts Used:
- 134616100
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Original bellow had 2 largish holes in the upper left quadrant; random leaking.
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfec
... Read more
tly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from DAYTON, OH
- Parts Used:
- 134937300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Broken door latch
First, I went to the PartSelect website and easily found the part at a reasonable price. I ordered it early on a Wednesday afternoon, and gladly spent the extra $25 to ship it overnight. That evening, PartSelect sent me an email stating that the part had shipped that very day, and - mistakenly - I took that literally. FedEx tracking predi
... Read more
cted that the part would arrive on Friday, July 5, which made sense because the 4th was a holiday.
But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July.
That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping.
Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes.
But no thanks to PartSelect.
But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July.
That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping.
Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes.
But no thanks to PartSelect.
Read less
Was this instruction helpful to you?
Thank you for voting!
Electrolux Upright Washer Door Wouldn't Open
Parts took twice as long to arrive shipped from Utah to Houston, Texas. Once arrived parts were straight forward to install.
1) Open the door by tripping the door strike using yard trimmer line.
2) Turned Power off (unplugged unit)
3) Used needle noses pliers to remove door rubber boot retainer
4) Folded right-side ... Read more of rubber in to removed switch assembly
5) Used Phillips screwdriver to remove switch assembly screws, navigated damaged switch part forward then disconnected line.
6) Connected new switch to line, navigate part back into washer and screwed back in.
7) Repositioned door rubber boot and reattached door boot retainer wire with hands and needle noose pliers.
8) Replaced door strike using Phillips screw driver.
9) Re-plugged washer power to outlet, closed door and ran a test cycle. All good!
1) Open the door by tripping the door strike using yard trimmer line.
2) Turned Power off (unplugged unit)
3) Used needle noses pliers to remove door rubber boot retainer
4) Folded right-side ... Read more of rubber in to removed switch assembly
5) Used Phillips screwdriver to remove switch assembly screws, navigated damaged switch part forward then disconnected line.
6) Connected new switch to line, navigate part back into washer and screwed back in.
7) Repositioned door rubber boot and reattached door boot retainer wire with hands and needle noose pliers.
8) Replaced door strike using Phillips screw driver.
9) Re-plugged washer power to outlet, closed door and ran a test cycle. All good!
Read less
Was this instruction helpful to you?
Thank you for voting!