Models > CAW9244BW0

CAW9244BW0 Crosley Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for CAW9244BW0

Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
The lid latch is a safety feature found in your washer. Its purpose is to stop the machine from spinning when the lid is opened. You may need to replace the lid latch assembly if your washer will not ...
In Stock
Order within the next 55 mins and your part ships today!
The suspension rods help to keep the tub in your washing machine stable and secure while cycling through your laundry. If your washer is excessively vibrating, moving around, or very loud when operati...
In Stock
Order within the next 55 mins and your part ships today!
The drive belt works with the pulley in your washer in order to spin the tub. If you notice a burning rubber smell, your washer has become excessively noisy, or it will not spin, it could indicate an ...
In Stock
Order within the next 55 mins and your part ships today!
The washer drive pulley kit is also known as a replacement clutch assembly, or a cam kit. The drive pulley is found at the bottom of your washing machine, mounted to the drive shaft. Common symptoms i...
In Stock
Order within the next 55 mins and your part ships today!
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order within the next 55 mins and your part ships today!
If your washing machine is shaking, noisy, or moves while operating, you may need to replace the suspension rod supports. These supports are used to secure the suspension rods, which help ensure that ...
In Stock
Order within the next 55 mins and your part ships today!
In Stock
Order within the next 55 mins and your part ships today!
This part changes the transmission from agitation to spin mode. This actuator is for washers. Actuator shifts the splutch and monitors the position of the splutch.
In Stock
Order within the next 55 mins and your part ships today!
This part goes on the agitator retaining bolt.
In Stock
Order within the next 55 mins and your part ships today!
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
In Stock
Order within the next 55 mins and your part ships today!
This insert is sold individually. Knob not included. Knob is sold separately.
In Stock
Order within the next 55 mins and your part ships today!
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
In Stock
Order within the next 55 mins and your part ships today!

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for CAW9244BW0

Viewing 11 of 11
Will not agitate
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not drain
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Lid or door won’t close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Spins slowly
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Burning smell
Fixed by these parts
Fixing Fixing
How to fix it
Shaking and Moving
Fixed by these parts
Fixing
How to fix it
Spinning Issues
Fixed by these parts
Fixing Fixing Fixing
How to fix it
No hot or cold water
Fixed by these parts
Fixing
How to fix it
Locking Issues
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
  • Customer:
    David from Los Alamos, NM
  • Parts Used:
    WPW10006355
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Lid Lock light blinking, machine will not start
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
308 of 383 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Terry from Homosassa, FL
  • Parts Used:
    W10780048
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
Violent shacking in spin mode.
Watched a video on the internet.
180 of 218 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    William from Wakefield, RI
  • Parts Used:
    W10404050
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Defective lid latch - Cabrio Washer
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
88 of 105 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!