Models
>
CW6000W
CW6000W Crosley Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for CW6000W
Viewing 11 of 11Keep searches simple, eg. "belt" or "pump".
$10.97
This is a V-style drive belt that measures approximately 51-inches long and 3/8-inches wide. This part connects the drive motor to the drive system in the washer to turn the basket. It is prone to wea...
In Stock
$11.77
This suspension spring is used with many washing machines. It is made entirely of metal and is seven inches long.
In Stock
$11.17
This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.
In Stock
$22.22
This lid hinge pin is just over an inch long. It is all white in color and is made entirely of plastic. Sold individually.
In Stock
$84.55
This pump has 2 ports. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
In Stock
$120.02
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. NOTE: This is a redesigned part. The pump now mounts on to the b...
In Stock
$13.09
This snubber ring fits washers and is located between the leg and dome assembly. The ring has a diameter of 9 inches. It is used to reduce noise and vibration for stability when the washer is operatin...
In Stock
Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY availab...
In Stock
$5.41
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
$11.77
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
In Stock
This package contains a new set of six springs. The suspension springs in your washer connect to the bottom of tub, and help to hold it in place. If your washer tub shakes, or moves around a lot durin...
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for CW6000W
Viewing 11 of 11Leaking
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Boca Raton, FL
- Parts Used:
- WP35-6465
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
washing machine was making alot of noise
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again.
Was this instruction helpful to you?
Thank you for voting!
One of the plastic hinge pins brroke
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ranse from Layton, UT
- Parts Used:
- WP35-6780, WP21352320
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
Pump was making a grinding noise
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A
... Read more
small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it.
Read less
Was this instruction helpful to you?
Thank you for voting!