Models > LNC6766A71

LNC6766A71 Admiral Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for LNC6766A71

Viewing 6 of 6

Manuals & Guides for LNC6766A71

Click to download
Keep searches simple, eg. "belt" or "pump".
This suspension spring is used with many washing machines. It is made entirely of metal and is seven inches long.
In Stock
This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.
In Stock
This lid hinge pin is just over an inch long. It is all white in color and is made entirely of plastic. Sold individually.
In Stock
This pump has 2 ports. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
In Stock
This snubber ring fits washers and is located between the leg and dome assembly. The ring has a diameter of 9 inches. It is used to reduce noise and vibration for stability when the washer is operatin...
In Stock
Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY availab...
In Stock
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
$11.80
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
This motor is a 2 speed, 1/2 HP, 120V, 60Hz.
In Stock
This is a multi-use cover screw. It fits appliances such as dryers, ranges, washers, dishwashers, refrigerators, air conditioners, washer dryer combos, freezers, wall ovens, microwaves, dehumidifiers,...
In Stock
This water valve is for 60% hot water and 40% cold - This is done to save on energy.
In Stock
$11.10
This hose clamp is sold individually.
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for LNC6766A71

Viewing 10 of 10
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not agitate
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Lid or door won’t close
Fixed by these parts
Fixing Fixing
How to fix it
Will not drain
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Burning smell
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Spins slowly
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
No hot or cold water
Fixed by these parts
Fixing Fixing
How to fix it
Shaking and Moving
Fixed by these parts
Fixing
How to fix it
Spinning Issues
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
David from Boca Raton, FL
Parts Used:
WP35-6465
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench set
washing machine was making alot of noise
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again.
561 of 571 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Allen from North Little Rock, AR
Parts Used:
WP35-2045, WP35-2044, WP25-7893
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
One of the plastic hinge pins brroke
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
512 of 515 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Butler, PA
Parts Used:
WP21002026, WP21001598
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set
Washer jumping in spin cycle (white flakes under the washer)
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING (DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK) Install the new ring, tighten the screws and put the tub back in connecting everything back up and use the 6 new springs. It really isn't that hard to do.
288 of 301 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!