CET8000AQ1 Whirlpool Washer Dryer Combo - Instructions

First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes.

Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and didn't take but 15-20 minutes.

Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.

I started to repair this and got busy and ended up calling a repair service -- that was the first time. They repaired it for over $200 and said the cause was bad venting. I fixed the vent before using the fixed dryer but it blew again. So I ordered these parts and replaced them myself for a lot of savings. However, the dryer still overheated. Through lots of testing I found the root cause the repairman missed: The heating element had gotten so hot that the assembly holding it warped, hitting the element and shorting it. So a new element is on order. I still needed the parts I ordered here but the overall repair ended up more complicated and expensive. I was disappointed a paid repair person left without further diagnosis. If he had unplugged the vent and checked the heat on the exhaust vent (as I ended up doing) it would have been obvious more than a new thermal fuse/thermistor was necessary. Instead I wasted over $200 on his visit. So my advice is if you're at all handy, repair this yourself. The dryer has a service manual inside the front toe board that walks you through most diagnostics and tests. However, it took a little more than that for me to discover the heating element problem. This was a very dangerous situation that could have easily led to a fire, yet not found by a trained technician!

Removed the front panel unplugged
The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.

ordered new lint screen, removed old screen, inserted new screen.

I can't believe I waited so long to find this part and do this. I got the package very fast, opened it, took the piece to my dryer and popped it into place with my fingers. It worked perfectly! this took all of two minutes and saved me from having to hold the dryer door closed with a stick. Thank you, thank you!!!

This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.

Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.

This do it yourself repair saved me the cost of a repair man's service call plus time to put it in. 1. First of all, make sure the unit is unplugged. On this type of front loading washer you will need to remove the bottom panel, which is secured by 3 nut screws. 2. Once the panel is removed you will need to use pliers to unscrew the drain plug and allow for excess water to drain out before removing the drain pump (get a pan or something that will fit underneath the drain). This is the area in which all the loose stuff, like coins and everything else falling out of pockets, gets trapped. The trap works well and needs to be checked periodically or if left unchecked it will probably be the cause of burning up the drain pump. 3. Once the water is drained you will need to use pliers to unsecure the two hoses attached to the drain pump. The pliers will pinch the wire clamps open and you can remove the hose easily. 4. The dryer is stacked on top of my washer and in order to get to the two screws holding the drain pump I needed to put a block of wood under the washer to give myself room to get a wrench to the screws. Once the dryer and washer were unloaded and nothing on top I was able to lift the washer and slide a block of wood underneath. 5. The pump has a power supply on the right hand side (a small white box with a wire attached) Remove the wire by gently pulling on the end of it. It is a plug type end. 6. Using a wrench (or socket driver) I took out the two screws (about an 1.5"). The drain pump slides to the right and out it comes. It is also secured by two rubber seals which are easy to remove as well as to install. 7. Now all you do is work backwards, installing the new drain pump by sliding the seals in place and wrenching the screws back in to hold the drain pump, followed by putting the two hoses back on with the pliers and placing the wire back into the power supply box on the drain. I would recommend anyone being able to do this on their own or at least with another person to help with a bit of lifting. The only way I knew to replace this part was because it was making all the noise, so it doesn't take much rocket science :)

The issue was the idler pulley. First I began opening up the front panel based on a youtube video but soon realized the model was slightly different and required a lot more items to remove. I saw the pulley in the back with nothing in the way so I put the front panel crap back on and removed the rear panel. There it was, very simple to remove and replace. I'm not looking forward to drum rollers though. Hopefully they're aren't as difficult as they appear.

I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks

I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the unit...works fine

Found this site by googling, and it works! I searched lint filters and just ordered based on how it looked...LOL! Husband wasn't home, it looked pretty much like the one I had in my hand, so.... I ordered it. It is the perfect fit and seems to have a tighter gasket glued in all around the screen. Let's hope this one lasts longer than 6 months! Thank you Parts Select for being so fast!! Filter got here in less than 48 hrs.!

use screwdriver topry plastic out plyers to pull out metal latch put new parts in