Models > LTKA6AQN4350

LTKA6AQN4350 Speed Queen Washer Dryer Combo

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for LTKA6AQN4350

Viewing 26 of 26
Keep searches simple, eg. "belt" or "pump".
This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both h...
In Stock
This washer is 3/4 inches in diameter.
In Stock
This metal retaining ring is well under an inch long. Use it for your Maytag brand clothes washer or your clothes dryer.
In Stock
This part replaces older two terminal switches.
In Stock
This part is located between the back of the drum and the rear dryer panel.
In Stock
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
This front cover spring retaining clip is not quite an inch long. It is made entirely of metal and is used for some washing machines.
In Stock
$11.10
This hose clamp is sold individually.
In Stock
$45.24
The bracket is no longer included.
In Stock
This high pressure inlet hose washer is black. It is an inch in diameter, made of rubber, and used with many washing machines, refrigerators, and dishwashers.
In Stock
This screw is sold individually.
In Stock

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for LTKA6AQN4350

Viewing 7 of 7
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing
How to fix it
Not Heating
Fixed by these parts
Fixing
How to fix it
Will not agitate
Fixed by these parts
Fixing Fixing
How to fix it
Burning smell
Fixed by these parts
Fixing Fixing
How to fix it
Spins slowly
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Gary from Haverhill, NH
Parts Used:
279834
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
Dryer ran but would not heat
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.
390 of 439 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
andy from Bethesda, MD
Parts Used:
279834, 279834
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Dryer flame goes out after about 8-minutes from start and won’t work again until a 15-minute rest.
There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils & the problem was corrected.
202 of 224 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joaquin from Las Vegas, NV
Parts Used:
279834, 279834
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Timer wasn't working (New Timer)
Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I or dered the coils for the valves, replaced both valves and tested the dryer and it work just like when I first bought the appliance.
158 of 198 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!