Models
>
MLE20PDBGW2
MLE20PDBGW2 Maytag Washer Dryer Combo
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for MLE20PDBGW2
Viewing 14 of 14
Keep searches simple, eg. "belt" or "pump".
$61.46
If the lint filter in your dryer has become damaged and unusable, it is important to replace it as soon as possible. The filter traps lint and other debris from your laundry, keeping it out of your ai...
In Stock
$22.69
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the d...
In Stock
$40.54
This is a genuine OEM replacement igniter kit for your gas-heated clothes dryer. The silicon carbide igniter is used to light the gas that creates the heat in order to dry your clothes. If your dryer ...
In Stock
$13.42
This small but mighty OEM piece is called a tri-ring and is used to support the drum roller shaft and the idler pulley shaft in your dryer. It helps to provide a tight seal between components by evenl...
In Stock
$47.74
The internal-bias thermostat, also know as a thermistor, is used to prevent the dryer from overheating. It does this by monitoring and controlling the temperature of the inside of the dryer drum. If ...
In Stock
$47.91
This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allo...
In Stock
In Stock
$124.64
This motor fits most Whirlpool incorporated dryer brands before 1996. NOTE: Pulley is NOT available separately.
In Stock
This heating element connection wire kit is a genuine OEM replacement for your electric dryer. The kit is used to connect the thermostat to the heater element. The kit comes with a yellow wire nut and...
In Stock
In Stock
$5.42
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
$57.18
Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles. This shock absorber is for washers.
Shock absorber absorbs the vibrations and movements of the oute...
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for MLE20PDBGW2
Viewing 15 of 15Noisy
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Locking Issues
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JEFFREY from FALL RIVER, MA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
felt strip came off lint screen
ordered new lint screen, removed old screen, inserted new screen.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Moscow, IA
- Parts Used:
- 279827
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Make humming noise when pressing start button. Would not start
After looking on the website for advice I walked throught the simple steps of disassembling the front, removing the drum, removed the back, disconnected the wire harness. Then removed the blower housing in the back. The blower, mounted on the back side of the motor was very tight. I used a pipe wrench wedged in place and help by my 10
... Read more
year old Grand-daughter while I used an adjustable wrench to turn the shaft on the front of the motor. Spun the blower off, removed the two clips holding the motor. Then reversed the process when I received the new motor. Care should be taken to avoid damaging the blower fan if a lot of pressure is required.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Mt. Pleasant, SC
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
catch mounted on door broke
The door had always opened with the wrong swing and it wasn't til I needed to repair this that I noticed you could change the swing. I changed the swing of the door and then noticed that the clip was included on both sides so i did not need to repair the catch. I still have the part so when it breaks again, I can just pop it in.
Was this instruction helpful to you?
Thank you for voting!