Models > LSE7804ACE

LSE7804ACE Maytag Washer Dryer Combo

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for LSE7804ACE

Viewing 18 of 18

Manuals & Guides for LSE7804ACE

Click to download
Keep searches simple, eg. "belt" or "pump".
This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommen...
In Stock
This is a single OEM dryer drum belt. It measures 100 inches in length, 3/8 of an inch wide and has five ribs and four grooves. Keep in mind that this rubber drum belt will stretch over time, so if yo...
In Stock
This part is located on the front bulkhead of the dryer and helps the drum to rotate smoothly and quietly. If you notice a screeching or metal-on-metal noise while your appliance is operating, you may...
In Stock
$9.48
The roller shaft is also known as a support roller shaft or a drum roller axle. It is a part in your dryer that the drum rollers spin on, helping your dryer to tumble. If your appliance is noisy while...
In Stock
The blower wheel is responsible for blowing heat into the dryer drum, and out of the exhaust vent. If you notice that your dryer is taking too long to dry or is make unusually loud noises, it may be t...
In Stock
Over time, the belts in your washer can either stretch out and sag, or become brittle and snap. When this happens, it can result in the belt losing its grip and will not be able to spin or drain the t...
In Stock
This lint filter is a genuine OEM replacement part for your dryer. The lint filter is used to trap debris and prevent it from clogging up your dryer vents. If your lint filter has become damaged it sh...
In Stock
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is nois...
In Stock
This roller shaft washer is just under an inch in diameter and is used for some of Whirlpool's brands of clothes dryers.Sold individually.
In Stock
This kit comes in two pieces: the catch and the clip.
In Stock
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
In Stock
This part is used to help the belt to rotate the drum. It is white and made of plastic with a metallic bearing in the center.
In Stock
Questions and Answers

Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

1 question answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gary
October 11, 2021
Washer will fill with water but will not agitate
For model number LSE7804ACE
Hello Gary, Thank you for the question. If there is no noise such as the motor trying to agitate. we suggest testing or replacing the Lid Check Switch. This is used to start your washer once the desired water level is reached. NC to COM should read closed and NO to COM should read open. They should reverse when you press the button. We hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:

Common Problems and Symptoms for LSE7804ACE

Viewing 21 of 21
Noisy
Fixed by these parts
How to fix it
Will not tumble
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
No heat or not enough heat
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Shakes and moves
Fixed by these parts
How to fix it
Takes too long to dry
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Pumps but will not spin
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Will not stop filling with water
Fixed by these parts
How to fix it
Will not shut off
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Timer will not advance
Fixed by these parts
How to fix it
Shuts off too soon
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
  • Customer:
    Stephen from Lafayette, IN
  • Parts Used:
    Y303836
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
The blower fan (nylon) stripped off the motor shaft (steel)
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
559 of 563 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Raymond from West Bend, WI
  • Parts Used:
    WPY312959, Y303836, WP33001003
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable)
electric dryer was rumbling - wheel or belt?
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through. Put the tumbler back on and reached back with both hands to thread it. Took a half dozen tries until I was sure it was seated correctly and not twisted. Put front... of dryer back on. So far (a week or so) the rumble is gone. Seems blower wheel was the cause of the rumble. Belt didn't seem worn but replaced anyhow.
592 of 697 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Charles from Whitman, MA
  • Parts Used:
    12112425, 12112425
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Drum would not drain and there was a banging noise when the drum spun
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
544 of 586 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!