Models > TCW2013OS

TCW2013OS (ASSEELC) LG Washer Dryer Combo

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for TCW2013OS

Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
Regulate the washer?s hot water supply with this single-solenoid inlet valve. It links the household hot water line to the internal filling system, opening on a control request and closing when the fi...
In Stock
Order now and your part arrives by Nov 23
Hold the door slightly open between loads, allowing air to circulate through the drum and around the door seal with this washer magnetic door plunger. This helps trapped moisture dry and reduces musty...
In Stock
Order now and your part arrives by Nov 23
The suspension shock absorber connects the tub to the cabinet base and resists sudden movement as the load turns. A worn or damaged absorber may allow excessive shaking, thumping, or repeated unbalanc...
In Stock
Order now and your part arrives by Nov 23
The motor rotor position sensor monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer is displaying an LE error code ...
In Stock
Order now and your part arrives by Nov 23
Cold water reaches the washer tub and dispenser through this triple-solenoid inlet valve assembly. Its three controlled outlets open during selected cycle stages, directing water where needed before c...
In Stock
Order now and your part arrives by Nov 23
Water and detergent travel from the dispenser into the washer tub through this flexible rubber dispenser hose. Its bellows folds allow the hose to flex as the tub moves during operation, helping maint...
In Stock
Order now and your part arrives by Nov 23
No Longer Available
$26.19
The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.
Special Order
In Stock
Order now and your part arrives by Nov 23
In Stock
Order now and your part arrives by Nov 23
$16.45
This hose clamp applies pressure around the hose end, holding it firmly against its fitting during operation. A secure hose connection helps keep water contained inside the appliance. This OEM part is...
In Stock
Order now and your part arrives by Nov 23
If your washer isn’t locking or starting like it should, this replacement door lock switch could be the fix you need. It helps your machine know when the door is closed so it can lock and begin the cy...
In Stock
Order now and your part arrives by Nov 23

Common Problems and Symptoms for TCW2013OS

Viewing 11 of 11
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Lid or door won’t close
Fixed by these parts
Fixing Fixing
How to fix it
Water Filling Issues
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Spinning Issues
Fixed by these parts
Fixing Fixing
How to fix it
Locking Issues
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not agitate
Fixed by these parts
Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Shaking and Moving
Fixed by these parts
Fixing
How to fix it
No hot or cold water
Fixed by these parts
Fixing
How to fix it
Will not drain
Fixed by these parts
Fixing Fixing
How to fix it
Spins slowly
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mark from Harrisburg, PA
Parts Used:
6501KW2002B
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
LE Error Message and won't spin drum properly
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
255 of 339 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Omnitech from Warrenville, IL
Parts Used:
AGM73610701
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Door would not close
There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replac e the magnet was $18. Instructions were included in the box. Part number on the drawing was A165. PS3618292 Magnetic Door Plunger
157 of 181 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Northport, NY
Parts Used:
5221ER1003A
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Inlet valve leak
Followed directions on the video and went like a charm. Very impressed with service and video
34 of 37 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!