Models > WM3488HW

WM3488HW (ABWEEUS) LG Washer Dryer Combo

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for WM3488HW

Viewing 4 of 4
Keep searches simple, eg. "belt" or "pump".
This is a drain pump motor assembly for washers. This OEM part is responsible for removing water from the washer during the drain part of the cycle. When this part is clogged, damaged or defective it ...
In Stock
Order now and your part arrives by Nov 23
Regulate the washer?s hot water supply with this single-solenoid inlet valve. It links the household hot water line to the internal filling system, opening on a control request and closing when the fi...
In Stock
Order now and your part arrives by Nov 23
A rubber barrier around the rotating drum shaft helps protect the washer?s tub bearings from water and detergent. This rear tub shaft seal sits in the rear outer tub, keeping wash water out of the bea...
In Stock
Order now and your part arrives by Nov 23
This washer rear tub ball bearing supports smooth drum rotation. Located at the back of the outer tub, it supports the inner drum shaft and reduces friction during washing and spinning. Installing a r...
In Stock
Order now and your part arrives by Nov 23
$38.45
The removable filter and cap assembly provides access for routine cleaning and seals the filter opening when tightened. Replace the damaged assembly to restore the debris trap and sealed access point....
In Stock
Order now and your part arrives by Nov 23
Tub bearing. This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly.
Special Order
$26.19
The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.
Special Order
$16.45
This hose clamp applies pressure around the hose end, holding it firmly against its fitting during operation. A secure hose connection helps keep water contained inside the appliance. This OEM part is...
In Stock
Order now and your part arrives by Nov 23
If your washer isn’t locking or starting like it should, this replacement door lock switch could be the fix you need. It helps your machine know when the door is closed so it can lock and begin the cy...
In Stock
Order now and your part arrives by Nov 23
Drain residual water before cleaning the pump filter with this washer cleanout hose. The flexible rubber hose attaches to the drain pump filter housing, giving remaining water a controlled outlet from...
In Stock
Order now and your part arrives by Nov 23
This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before be...
No Longer Available
In Stock
Order now and your part arrives by Nov 23

Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

1 question answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
CHRISTOPHER
March 10, 2024
Dryer not drying
For model number WM3488HW
Fix.com logo
Hello Christopher, thank you for contacting us. Based on our understanding of the issue, we would suggest replacing the heating element, part number FIX3527798, to solve the problem. It generates the heat to dry clothes when you select the dry cycle option. We hope that helps!

Was this helpful?
Thank you for voting!
Related Parts:

Common Problems and Symptoms for WM3488HW

Viewing 14 of 14
Will not drain
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Draining Issues
Fixed by these parts
Fixing
How to fix it
Water Filling Issues
Fixed by these parts
Fixing
How to fix it
Locking Issues
Fixed by these parts
Fixing Fixing
How to fix it
Engine runs but does not pump water
Fixed by these parts
Fixing
How to fix it
Lid or door won’t close
Fixed by these parts
Fixing
How to fix it
Noisy and Marks Left on Clothes
Fixed by these parts
Fixing Fixing
How to fix it
No hot or cold water
Fixed by these parts
Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing
How to fix it
Burning smell
Fixed by these parts
Fixing Fixing
How to fix it
Spinning Issues
Fixed by these parts
Fixing Fixing
How to fix it
Noisy
Fixed by these parts
Fixing
How to fix it
Not draining
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jorge from Apple Valley, CA
Parts Used:
4681EA2001T
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
592 of 761 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from RALEIGH, NC
Parts Used:
4681EA2001T
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
noisy operation, sometimes did not drain, gave OE code
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
60 of 81 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from COTTAGE GROVE, WI
Parts Used:
4681EA2001T
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Pump rotor broke off shaft.
There are two pumps in this system. I turned the washer on its side and took off bottom plate. There are several screws holding this on. I then took the entire pump assembly off. There are 3 screws holding each pump on the brown plastic body. Each pump has a positive and negative lead. I switched out the pump and reassembled. The h ardest part is getting the 3 "shock absorbers in place with the rubber sleeves. I think the book suggest getting to the pump from the front side but I went through the bottom. Worked good. I did wonder however if the other pump was working. Do you need two pump working to get flow? By replacing one pump I went from no flow to good flow. Cost me $75.00
23 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!