Models > 1106109801

1106109801 Kenmore Washer Dryer Combo

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This 10-watt clear bulb provides dependable lighting inside dryers and refrigerators, helping you see the interior clearly when the door is open. Compatible with a variety of appliance models, it inst...
In Stock
Order now and your part arrives by Jun 6
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order now and your part arrives by Jun 6
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
Order now and your part arrives by Jun 6
This hose clamp is sold individually.
In Stock
Order now and your part arrives by Jun 6
This part is used to secure the top panel to the cabinet. Sold individually.
On Order
Found on the water inlet valve.
Special Order
This screw is sold individually.
No Longer Available
This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.
In Stock
Order now and your part arrives by Jun 6
With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 250 degrees Fahrenheit. The element will kick back in when the temperature drops to 210 degrees Fahrenh...
No Longer Available
Part may differ in appearance, but functions same as original.
Special Order
Sold Individually. Order quantity needed.
Special Order
This two piece oil seal kit comes in two pieces and is used for the gearcase input shaft of your washer.
In Stock
Order now and your part arrives by Jun 6

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for 1106109801

Viewing 3 of 3
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Too hot
Fixed by these parts
Fixing
How to fix it
Will not drain
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mason from New Park, PA
Parts Used:
279052
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
No heat
I removed the old thermostat. One of the wires was fried. The new thermostat came with a new clip/connector so I cut the bad part of the wire out, stripped it back and attached the new connector. Then, I screwed the new thermostat in place and attached both connectors. The dryer has heat again. PartSelect.com got the correct part out to m e in a short amount of time. Their repair help also helped me test and diagnose the problem in the first place.
16 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Huntington Station, NY
Parts Used:
WP18776
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
broken clip on top panel hold down
pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.
15 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Peter from Richmond, KY
Parts Used:
279052
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Socket set
While removing 21 years of coins and lint I damaged the factory installed thermostat limit switch.
Remove damaged switch and install new one
8 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!