Models
>
WSM2420SDZWW
WSM2420SDZWW General Electric Washer Dryer Combo
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for WSM2420SDZWW
Viewing 11 of 11Keep searches simple, eg. "belt" or "pump".
On Order
$133.26
Used with washer/dryer combos. This part makes sure that the lid is shut before allowing the machine to start or agitate.
In Stock
Order within the next 10 mins and your part ships today!
$61.67
This fuse is made to trip at a higher temperature than the high limit thermostat. When this fuse trips, it will no longer work. You must replace it.
In Stock
Order within the next 10 mins and your part ships today!
In Stock
Order within the next 10 mins and your part ships today!
$288.95
The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
In Stock
Order within the next 10 mins and your part ships today!
In Stock
Order within the next 10 mins and your part ships today!
These parts help keep the washer from vigorous shaking during its cycles.
No Longer Available
In Stock
Order within the next 10 mins and your part ships today!
Special Order
In Stock
Order within the next 10 mins and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for WSM2420SDZWW
Viewing 1 of 1Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Burnt Hills, NY
- Parts Used:
- WH12X950
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washing machine would not cycle properly
Our washing machine had gotten stuck in the agitation cycle several times....it wouldn't cycle out of either wash or rinse, and was clogged with suds. Turns out we were using the wrong detergent, one recommended only for front-loading high efficiency washers. I removed knobs and front panel, then the two screws holding the timer mechanism
... Read more
in. Although it looked nearly new, clearly it didn't work. The replacement part arrived in two days, and was easy to install.- 5 screws holding the panel, and 2 on the timer. tested the washer today, and it worked perfectly.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Signal Mountain, TN
- Parts Used:
- WH45X144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Agitator was shredded
The agitator broke free while the washer was spinning and it shredded the plastic. All I had to do was remove a little top cap off the agitator by prying it up with a screwdriver, then replacing the cap on the new agitator. Viola! Done. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cami from Roswell, GA
- Parts Used:
- WH12X955
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken lid switch (old part worked, but plastic casing broke and screws couldn't hold it in place anymore)
The removal and installation were self-explanatory once the part was in hand. Because the unit is in a laundry closet off the bathroom, space was limited and we had to be creative. Hence, my son's Handy Manny tool set, Turner to be exact, was perfect for holding the ground wire bolt in place from behind the dryer lid so that we could loos
... Read more
en the nut on the inside of the dryer lid. Of course, when I went to put the nut back on the bolt after putting the new ground wire in place, I dropped the nut in the dryer. That's when our son's Harvey the train (a Thomas the Tank engine character) came in handy. My long arms and its magnet were just the thing to get the nut out of the abyss at the bottom of the washer cabinet.
Read less
Was this instruction helpful to you?
Thank you for voting!