WSM2700WBAA General Electric Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack from Canyon Lake, TX
- Parts Used:
- WH23X10041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Washer would not drain
Removed 2 Hose clamps with pliers. Unplug power source from drain pump. Unscrew 2 mounting screws with 5/16" nut-driver then replace unit in reverse sequence...... Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from chicago, IL
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
filter had a hole
simple replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from coldwater, MI
- Parts Used:
- WE3X70, WE13X28680
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
load noise
took the top off, then the front,there 2 screws that hold the front on. there's a yellow thing on the front took that off, it is held on with one screw. on the back of the dryer on the bottom is a metal plate take that off, to get to the belt take that off. then there' 3 screws in the drum, take them off ,then you can slid the drum out. then take 2 screws off the bearing bracket, that's it. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Battle Ground, WA
- Parts Used:
- WE3X70
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was squeeking for a while, and then eventually just quit working.
Took the top and the front panel off (took me a while to figure this out without breaking stuff). Took off belt, pulled out drum, replaced bearing, and then I also had to replace the ball (attached to rear of drum, which slides inside the bearing).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Orlando, FL
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Nasty, rusted lint trap didn't function any longer
The part arrived in just a couple of days and was exactly the right one. Simply removed the old and replaced and now the dryer works 100 percent better. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROSANNE from CENTRAL ISLIP, NY
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
had dropped the dryer filter in the washing machine
the repair was completed with a new lint filter. easy in, the old one tossed out.....perfect/ i'm amazing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from SILVER SPRING, MD
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter was damaged.
Took a chance on the size and luckily filter was perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from ROCKAWAY, NJ
- Parts Used:
- WE16X29397
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dyer lint filter had holes in the screen
Just installe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NICOLAS from LYNN, MA
- Parts Used:
- WE3X70
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Dryer making squeeky noise.
Removed the Drum and replaced the part....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Roselle, IL
- Parts Used:
- WH45X10018, WH08X10004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
left a drywall screw in my pockit and it cut the tub
I first made a repaire order online and put on the service order that i needed a new tub.
Someone was to call me the the night before but i never got the call the service man was
coming between 8am and 12 he called at 11
and wanted to come and look at the washer to see what parts he needed i told him i put in the service reqwest that it needed a tub and that if he didn't have the tub not to come because i was not going to pay for a service call if he didn't have the parts he did tell me it would cost me $430.00 so i repaired it myshelf
Someone was to call me the the night before but i never got the call the service man was
coming between 8am and 12 he called at 11
and wanted to come and look at the washer to see what parts he needed i told him i put in the service reqwest that it needed a tub and that if he didn't have the tub not to come because i was not going to pay for a service call if he didn't have the parts he did tell me it would cost me $430.00 so i repaired it myshelf
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Riviera Beach, FL
- Parts Used:
- WH07X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Spin cycle not spining sufficient water from clothes
Remove front of unit. Replace belt that drives the washer. This repair is very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Orange beach, AL
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter was bent and screen torn.
Ordered a new lint filter around 2 pm and received it UPS the following day. Popped it in and we're good to go. Could not have been faster or easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Silver Spring, MD
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
filter was busted
Replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from HALEYVILLE, AL
- Parts Used:
- WE3X70
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Lack of grease caused bearing to go out
I took the top and front off the dryer. I then took the screws out of the drum and removed the drum. I then took the old bearing out and put the new one in.
Was this instruction helpful to you?
Thank you for voting!