LC120JW4 Frigidaire Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timothy from Spring Valley, AL
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Williamsburg, MI
- Parts Used:
- 5308950197
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Leaking washing machine.
Removing the piece above the tub gasket was very difficult. A lot of hammer and chisel work.
15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove the old rubber stops. There were a few pieces. Then sealed it back up with the oil that came with the PartSelect Kit and put it back together. Works great now. No more LEAKS! Yippy.
15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove the old rubber stops. There were a few pieces. Then sealed it back up with the oil that came with the PartSelect Kit and put it back together. Works great now. No more LEAKS! Yippy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Baltimore, MD
- Parts Used:
- 5303280326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt worn causing machine to make all kinds of noise
pull up on top ,take two screws loose on front panel(pull off) vaccum old debri out,pull tension pulley back pull old belt off,holding tension pulley put new belt on .put front panel back on and snap top back down to secure.
working perfectly nice and quite !!!
working perfectly nice and quite !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maura from Bellingham, WA
- Parts Used:
- 5300633870
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Damaged lint filter
It was a snap....just replaced the old lint filter with the new one. But I want to say that this is the second time we've used PartSelect for replacement of parts on older appliances with great results. The parts were in stock and delivered very quickly. We'll certainly be using PartSelect again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Cumming, GA
- Parts Used:
- 5303280326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
drive belt replacement
removed rear panel, tilted machine forward, removed four bolts holding the pump and loosened the connection to the motor shaft,(several times dropped socket and without magnet to retrieve tools would have been much more difficult),removed two hoses, dropped pump assembly, replaced belt, and reversed the process to re-assemble. Easy to find part and will definitely use your parts finder again. Lots less expensive than repair service or replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tanya from KALISPELL, MT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The elements were not heating up
It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Falmouth, MA
- Parts Used:
- 5304409888
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Eldena, IL
- Parts Used:
- 5308015398
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer wont dry during one cycle, still doesn't
removed the two screws on the top at back of dryer then pryed up the front of the top, then removed the screws at the top of the front and pryed off the front of the dryer, the thermostat was at the bottom below the drum held on by two screws and had two wires on it. Fairly easy to replace but it did not solve my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Hartford, CT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Harrington, DE
- Parts Used:
- 5308015398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would not cut off on auto dry and after replacing the thermostat the problem still existed. Most likely something wrong with the timer part of circuit.
I decided to replace the cycling thermostat. I disconnected power, used the putty knife to push back spring type retainers underneath the top and
lifted up the front edge of the top and pushed it upward to rest on the back hinges.
Next, I unscrewed two sheetmetal screws on the edges of the front panel.
Then I supported the front panel upward while releasing the push type spring clamps before pulling it forward off the drum. I was able to swing
the front panel open from the left side and gently open it while watching one wire that was connected to it from the right side.
Then I was able to take the terminals off the thermostat noting which way they were connected.
I unscrewed the two screws holding the thermostat to the fan housing and replaced it with a new one. I assembeled from the front panel bacwards. until the top was back down.
Upon testing the unit I found out that the problem was not the cycling thermostat.
I plan to investigate the timer circuit that the thermostat controls next.
One can take out the thermostat and test it for cycling by removing it and checking terminals with ohmmeter x1 range and heating and cooling it with a hairdryer. Meter will read zero when thermostat is cold and closed. It will read infinity
or high resistance when it is open and hot.
lifted up the front edge of the top and pushed it upward to rest on the back hinges.
Next, I unscrewed two sheetmetal screws on the edges of the front panel.
Then I supported the front panel upward while releasing the push type spring clamps before pulling it forward off the drum. I was able to swing
the front panel open from the left side and gently open it while watching one wire that was connected to it from the right side.
Then I was able to take the terminals off the thermostat noting which way they were connected.
I unscrewed the two screws holding the thermostat to the fan housing and replaced it with a new one. I assembeled from the front panel bacwards. until the top was back down.
Upon testing the unit I found out that the problem was not the cycling thermostat.
I plan to investigate the timer circuit that the thermostat controls next.
One can take out the thermostat and test it for cycling by removing it and checking terminals with ohmmeter x1 range and heating and cooling it with a hairdryer. Meter will read zero when thermostat is cold and closed. It will read infinity
or high resistance when it is open and hot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from san leandro, CA
- Parts Used:
- 5308950197
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
leaking water
removed all parts from trans shaft and replaced seal although had some difficulty removeing the agitator assembly due to age and mineral deposits but a little wd40 and tapping with a hammer helped
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from WAPAKONETA, OH
- Parts Used:
- 5303280326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Worn out belt replacement
First unplug power cord and removed water hoses, then removed rear panel of machine. Shop-vac old debries out of machine Remove small spring holding belt tensioner pulley assembly. Remove hex key from motor shaft that connects to the pump. Use pliers to spin clamps out of way so you can then remove the (4) four bolts that hold pump to bottom of the motor, no need to remove other pump bolts. I used a straight screwdriver to pry the pump loose from the motor shaft to slip the old belt out of the machine. Put new belt on and reversed process for reassembly. :Note: Shop vac up water that leaks out of pump when you remove the 4 bolts, also wipe down pump so you can check for leaks after tightening pump back onto motor.
Was this instruction helpful to you?
Thank you for voting!