Models > B9307X0

B9307X0 Roper Wall Oven

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for B9307X0

Viewing 6 of 6

Manuals & Guides for B9307X0

Click to download
Keep searches simple, eg. "belt" or "pump".
Sold Individually.
In Stock
This blower wheel clamp is less than an inch long and is used for some clothes dryers to hold the blower wheel firmly in place. This green clamp is made of metal.
In Stock
This broil element is found on the roof of the oven and has push-on terminals.
In Stock
This temperature sensor is used with self cleaning ovens. Its 1000 ohm resistance increases with temperature. This sensor has male leads and comes with ceramic wire nuts.
No Longer Available
$8.04
10-32 hex - Sold Individually - Appliance originally takes 3 of this item.
In Stock
No Longer Available
No Longer Available
No Longer Available
No Longer Available
No Longer Available
No Longer Available
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for B9307X0

Viewing 7 of 7
Noisy
Fixed by these parts
Fixing
How to fix it
Little to no heat when baking
Fixed by these parts
Fixing Fixing
How to fix it
Little to no heat when broiling
Fixed by these parts
Fixing
How to fix it
Oven is too hot
Fixed by these parts
Fixing
How to fix it
Element will not heat
Fixed by these parts
Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing
How to fix it
Oven not heating evenly
Fixed by these parts
Fixing Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Charles from Brecksville, OH
Parts Used:
8053344
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
F3 Error message
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the strin g still shows thru the back. If you don't you have a 15 minute job trying to fish the wires at an angle thru the insulation (a very frustrating task). Untie the string from the old and tie it securely to the new. Pull the string from the back and Voila! your new sensor can be plugged in or wirer nutted to the old connection on the back of the stove. Replace the nut and the two screws and you're done!
157 of 198 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Starla from Vashon, WA
Parts Used:
WP660579
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Burnt out broiler element
Turned off power to range because I was scared. Unscrewed broiler element, pulled part forward and pulled off wires that were attached to the back, attached wires to new element, pushed it back in place, screwed it back on to oven. Cooked my bruchette!
19 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Albuquerque, NM
Parts Used:
WP330190
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
My stove top is 30 years old. I was down to one knob. I looked up the part by brand and age. the pictures were accurate and the size dimensions were perfect.
Pulled off the one remaining knob, installed the new ones. One minute and the stove works perfectly.
12 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!