CWE6230ADE Maytag Wall Oven - Instructions

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

I removed three screws, pulled the element out from the rear wall, unplugged the electrical connections, reversed these steps in installing the new element. "A Piece Of Cake!"

Purchased 2 piece broiler pan from this site

turned off electricity at the circuit breaker.Pulled stove out and looked at the way the control center was attached to the rest of the stove. Removed the knobs and 4 screws and the complete panel could be removed (or pulled out from the oven-wires are still all attached). Then checked with an electric meter to insure the power was off to all the wires. The clock is a self contained unit and all I had to do was to remove 4 screws holding a face plate, replace the unit and reverse the procedure. Only problem I had was getting the screws back into the face plate (I was only able to get 2 threaded-but that will hold for the life of the stove) and put it alll back together. It works wonderfully.

I had a repair company on the phone who said that the service call would be $185 and if I was right about the clock being the problem, that would cost another $345 for the clock and $85 for the return service call to install. I ordered the part from PartSelect .com on Sunday, had it by Thursday and installed that night. My cost was $195 vs approx $600. Why would you do anything else?

Had to disassemble the top of the stove and the control panel on the front. I took digital pictures as I disassembled so I could refer to them when putting the stove back together, especially when disconnecting wiring. It took about 3 hours, but most of that time was spent thoroughly cleaning 16 years of baked on grease from places that are normally unaccessible. The new latch works great - the wife is happy!

Removed 4 screws under the top unit that holds the stove control knobs. Open oven door for better view. Tilt whole unit (width of stove) up and out of top flange. Remove knobs for timer and the two control knobs (that operate the range burners) nearest the clock. Take out the screws by these knobs, 2 per knob and then you can get the frame that holds clock unit out. Make a drawing of wires to replace on timer unit or as I un plugged one I hooked it up to the new unit. Make sure you have turned off range at your fuse box before working on stove. Works good as new now, I assume it was hit by lighting that also made me replace our garage door opener.

removed 4 screws holding entire face plate. Rolled face plate up on top of stove and left all wires attached (many). removed 4 screws adjacent to clock assy. Removed control knob just on either side of clock assy and removed control screws (2 on each). removed wires attached to clock assy and transferred new assy. Re-assembled and set clock time.

First I verified that the breaker was OFF!

We have a build-in Jenn-Air oven. After finding the four screws that held the oven into the enclosure, sliding the oven out was pretty easy since my wife helped me. We used a nut drive to remove the 18+ screws holding the top on the oven.

Using the Internet we entered the switch part number. The number on the switch did NOT help finding the switch. We used the model number and with the exploded drawing on the PartSelect.com web site it was fairly easy to identify the switch.

I ordered the switch and specified two day delivery. This was on a Saturday. The switch arrived on Tuesday.

We had to remove the front glass plate to get to the screws holding the switch. I drew a diagram of the switch with the wire colors/numbers. I left the wires on the old switch. I removed the old switch with the wires still attached then installed the new switch. I moved the wires one by one. Then I verified the correct connections based on my drawing.

We re-installed the 18+ screws and slid the oven back into place. Turn on the breaker and baked a pie.

I didn't. Don't know how to get to light bulb to change it for this specific model

First I removed the four torx screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I installed the new element in reverse order. Recycled the cardboard box and the old element.

Removed the 4 screws on the bottom of the panel, lifted the panel out and up to clear the uper part of the panel. Removed the screws from the left and right switches, which hold the bracket of the clock, marked the wires of the clock and removed the wires. Installed the new clock in reverse. The power to the range was off.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

Part was perfect fit. Good product, good value, great service.

I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294