MEW9527FZ20 Maytag Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Carbondale, CO
- Parts Used:
- WP4449751
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
upper oven of wall oven would not heat suspected high temp limit switch
removed unit from cabinet tested switch it was OK checked wiring and found shorted out wire leading to switch. cut out bad section and spliced wire back together
problem solved
problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ROLESVILLE, NC
- Parts Used:
- W11185746
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Top vents allowing steam to escape from the microwave were condensing on the cabinet doors above.
Since the instructions and templates included didn't apply to my unit I had to improvise. The new Bump Out Bracket was way sturdier and thicker than the factory one removed. Very nice bracket!
Measuring down the wall from where the back of the cabinet actually touches the wall, down to the same distance as the microwave height (@ 15.5") I made a level line on the wall.
I positioned the bump out so the microwave would rest on the support at that measurement so when swinging the microwave into place the back top edge of the microwave would rest just below the wood of the cabinet. ( I went 1/8" lower to be safe). Then secured in place with two wall studs (I got lucky to find two) and two toggle bolts, one at either end of the upper bump out bracket.
Measured the distance for my front support screws in the upper cabinet and drilled two 5/16" holes. Used the same mounting screws in the upper cabinet and a flat washer on each for safety.
Measuring down the wall from where the back of the cabinet actually touches the wall, down to the same distance as the microwave height (@ 15.5") I made a level line on the wall.
I positioned the bump out so the microwave would rest on the support at that measurement so when swinging the microwave into place the back top edge of the microwave would rest just below the wood of the cabinet. ( I went 1/8" lower to be safe). Then secured in place with two wall studs (I got lucky to find two) and two toggle bolts, one at either end of the upper bump out bracket.
Measured the distance for my front support screws in the upper cabinet and drilled two 5/16" holes. Used the same mounting screws in the upper cabinet and a flat washer on each for safety.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from WEST CHESTER, OH
- Parts Used:
- W11185746
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
This was a "bump out" mounting plate so the microwave vent extended beyond the 14" cabinet front.
Templates provide in kit superseded those with microwave for mounting. This was somewhat easier than other options because we do not have a n exterior vent hookup. The template for the holes in the above cabinet needs to be positioned perfectly to make sure you drill the hole in EXACTLY the right place. Otherwise, this was straightforward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from FISHERS, IN
- Parts Used:
- W11454079
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light Burned out.
Simply removed light cover , extracted old bulb, placed the new bulb straight into the socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!