KODE500EWH02 KitchenAid Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Seattle, WA
- Parts Used:
- WP9755542
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
faulty meat probe
Not a repair. Just needed to replace the meat probe sensor for the programmable oven. Quick and easy purchase and very fast delivery took care of the problem. I was back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NORMAN from MISSION VIEJO, CA
- Parts Used:
- W10883049
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
LIGHT SWITCH ON LATCH-DOOR BROKEN
REMOVED PANEL COVER [ 4 SCREWS]
UNSCREWED 2 SCREWS ON LATCH DOOR
ON THIS MODEL THE PART WAS IN TOO TIGHT OF QUARTERS SO I HAD TO LOOSEN A TOP PANEL SO I COULD RAISE PART HIGH
ENOUGH TO RELEASE IT FROM A CATCH AT THE BACK OF THE PART. PUSH PART BACK, RAISE AND PULL FORWARDS.
REMOVED 4 WIRES ONE AT A TIME AND ATTACHING TO NEW PART. REPLACED PART, TIGHTEN TOP PANEL AND REPLACED PANEL COVER.
NOT BAD FOR A 91 YEAR OLD
UNSCREWED 2 SCREWS ON LATCH DOOR
ON THIS MODEL THE PART WAS IN TOO TIGHT OF QUARTERS SO I HAD TO LOOSEN A TOP PANEL SO I COULD RAISE PART HIGH
ENOUGH TO RELEASE IT FROM A CATCH AT THE BACK OF THE PART. PUSH PART BACK, RAISE AND PULL FORWARDS.
REMOVED 4 WIRES ONE AT A TIME AND ATTACHING TO NEW PART. REPLACED PART, TIGHTEN TOP PANEL AND REPLACED PANEL COVER.
NOT BAD FOR A 91 YEAR OLD
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from NEW WINDSOR, NY
- Parts Used:
- W10804429
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broil element was burned out
1. Turn off the breaker.
2. Remove all of the oven racks.
3. Remove the oven door as per users manual.
4. Remove two 1/4" screws on the plate holding the broil element
to the back of the oven.
5.. Remove two 1/4" screws in the front of the element holding
reflective plate and element toward the front of the oven.
6. Carefully pull the element out enough to remove the wire spade
contacts with from the rear of the element with long nosed pliers
being careful not to let the wires go behind the rear oven cavity.
7. Element and top reflective plate assembly can now be removed
from the oven.
8. The old element is removed from the reflective plate by removing
four 1/4" screws.
9. Install the new element on the plate and reverse the procedure to
reinstall the completed assembly into the oven.
10 Reinstall the door and racks, turn on the power and test.
2. Remove all of the oven racks.
3. Remove the oven door as per users manual.
4. Remove two 1/4" screws on the plate holding the broil element
to the back of the oven.
5.. Remove two 1/4" screws in the front of the element holding
reflective plate and element toward the front of the oven.
6. Carefully pull the element out enough to remove the wire spade
contacts with from the rear of the element with long nosed pliers
being careful not to let the wires go behind the rear oven cavity.
7. Element and top reflective plate assembly can now be removed
from the oven.
8. The old element is removed from the reflective plate by removing
four 1/4" screws.
9. Install the new element on the plate and reverse the procedure to
reinstall the completed assembly into the oven.
10 Reinstall the door and racks, turn on the power and test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Canyon Country, CA
- Parts Used:
- WP9755542
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb inop
Taking off the glass lense for the light bulb was harder than I thought. It unscrews counterclockwise, but it was very hard to get off. It would not turn. I ended up using connector pliers I use for work, that has rubber jaws. The lense unscrewed very easy with it. Light also unscrews out. PartSelect.com is the only way to go to buy parts for appliances. It is simple, even has the illustrated parts catalog. And it saves a lot of time and gas, driving around looking for the part!!. PartSelect came through again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from rochester, NY
- Parts Used:
- WP9755542
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The oven shipped without a temperature probe.
Unwrapped the package, plugged the probe into the oven, stuck the other end into the chicken.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from Chicago, IL
- Parts Used:
- W11718046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Decided to replace the stationary racks with rolling racks
To my amazement, they got here overnight. We unboxed them and put them in. Doesn't get any easier than that. Now all of the racks in my double oven are super easy to use when cooking. Wish you made rolling racks for the gas stoves (unfortunately, the ones for the double ovens were too big for the gas oven).Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Massey, MD
- Parts Used:
- WP9755542
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken meat probe
My story isn't so much about the repair but the fine service from part select. My 1st order was lost at delivery at our house. Part select quickly corrected the mishap with no issues. This kind of service is much appreciated.
Was this instruction helpful to you?
Thank you for voting!