79046602502 Kenmore Wall Oven - Instructions

Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.

I pulled my unit out of the wall and noticed that the insulation around the top broiler element was a bit brown. Closer inspection revealed that the element had shorted somehow to the oven itself and caused the element to become non-functional. I tried measuring the resistance first, and it was within typical values for the other elements, but I decided to replace the element anyway.

I ordered from PD and the part arrived just a few days letter by regular shipping. I undid the screws holding in the element, undid the wire connectors and replaced the broken element with the new one. The element worked like a charm and I was back in business for cooking.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

Removed old element and plugged in new. Very simple.

Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

Remove door per the manufacturer instructions (open the door and slide the keepers over the hook part of the hinge and then just pull the door out of the frame - no dismantling while attached to the oven), dismantled the door )about twelve screws around the perimeter of the door) and replaced both hinges. was much easier than I had anticipated. I ordered the parts regular fed ex ground and received within 3 days. I was totally surprised to get exactly what I ordered that fast. I would definitely use Partselect again. Great price and great service. Easy to order.

ordered switch for on, off. Turned power off at breaker.opened oven door, underneath top console there are four philip screws.. remove top and take slotted screwdriver and unscrew four plastic nuts. I used pocket knife..remove plastic cover , and then remove four more philip screws to remove metal plate that holds all four control switchs. remove two screws that held switch in place
and unplug wires and plug new switch in... Saftey first gentlemen, there is no ifs and buts or maybes when it comes to your life.. make sure you turn your power off.. works like a charm , can adjust heat from 1 to hi..thanks for partselect great price and speedy shipping...James K. Luper

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

Removed two screws holding broiler element. Released two spring hangers on near the front of the element. Pulled element away from oven and pulled two wire connectors off. Simply reverse process to install new one. Wasn't the problem.

Removed electrical connector and two screws. Attached the electrical connector to the new probe and attached with the two screws.

I removed the sensor from inside the oven with a 1/4” nut driver, pulled the sensor out slowly and then took the connection apart and found out that the connector was different, I cut the connector off of the oven side and then cut the connector off of the new sensor and wired it together. I am still trying to find the ceramic nuts. My oven is working for now. Very easy fix, just wish there were ceramic wire nuts with the new sensor

removed 1 screw from each glide, pulled parts out, replaced parts and screws, slid drawer glides into bearing glides. job done, very easy and fixed problem.

Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.

Cut power to your oven in your circuit breaker panel
Take out racks and bottom pan from the oven
Remove 2 screws in element bracket at back of oven
Lift element gently, tilt upward and pull towards you out of insulation
Get the tilted wire connectors clear of the back panel
Remove two wires from from connectors gently with your fingers
Take bad element out of oven
Replace it with new element
Replace everything else
Piece of cake. 20 minutes max: remove old; plug and play.