RGJ534GEP1 Hotpoint Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- eric from washington, DC
- Parts Used:
- WB32K5050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven door seal was old and falling apart
at first thought the seal would just slide out and the same for the replacement. when I realized that this was not the case and began to wonder what....? I saw the screws at top and bottom, took them off and voila the inner shell moved forward enough to take out the old, slide in the new, push in, replace the screws and back to a happy wife with an oven that can bake correctly again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from FORT BRAGG, CA
- Parts Used:
- WB21K5009
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
gas valve quit working
Very easy, didn't even have to take the oven out of the wall. Will use this site again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from SAVAGE, MN
- Parts Used:
- WB32K5050
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
the oven seal was dried out and crumbling not safe to use on a gas appliance
From what I was able to find info on I was to take out 5 screws 3 on top and 2 on the bottom then the inner oven box is suppose to pull out a bit to take the old gasket off and put the new onw on the box was so rusty it would not pull out so I was able to get enough of the box out using a large screwdriver the lip of the gasket tucks behind the box. I ended up using a small screwdriver to work the new gasket behind the oven box. The door now needs new springs the tension on them is not strong enough to pull the door shut the way it should there's still room to push the door into new gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Paso Robles, CA
- Parts Used:
- WB27T10327
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Electronic Control wouldn't stay on
Unplugged and pulled oven out, removed cover from top, removed control unit, prepared new control unit with jumper and face sticker, transferred wires from old unit to new unit, checked operation of new unit by plugging oven in... wooo hooo it works! reverse above steps... viola... done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from yANKTON, SD
- Parts Used:
- WB27T10327
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench set
would not heat the ignitor up at all.
The control kit came very fast only a few days. the instructions were ok but not that clear.....they have u add a jumper wire which is not hard to figure out but the fact that they say nothing about what wire needs to go from the other side of the relay. they say the yellow wire needs to go to no(the other lead on the relay)and that was not the case for my setup.i had to run my ornge wire from the ignitor to that side of the relay to get it to work when the instructions say to connect the sensor harness adapter to the same wire colors which had an ornge wire in it.so that was the only part that did not make sence. but other than that it works great.
Was this instruction helpful to you?
Thank you for voting!