JK1000DF3BB General Electric Wall Oven - Instructions

removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.

It took a while to remove approx 30 screws to get to the blower. So my oven was sitting, torn apart while I waited on the new blower fan that I had ordered. It arrived shortly, about 5 days. When I opened the box I saw that PARTSELECT had sent me a drain pump instead of the blower fan that I had ordered. Since an oven does not require a drain pump and it wouldn't work to replace my broken blower fan I had to return it. I was told that I needed to send the part back in order to get a refund. After I sent their drain pump back at a cost of $13 they emailed me and said I didn't need to send the drain pump back. And they refunded me minus shipping So I had to pay shipping both ways for a part that was wrong. And I ordered it from someone else. I put the new blower fan that I had bought from another company in and replaced the 30 screws. And the oven has been working fine ever since. Thank you PARTSELECT for allowing me to tell people how you operate. They have a money back guarantee, but they don't give you back ALL your money. Thanks Again.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Turn power off to oven, removed screws holding oven into cabinet, get assistance to remove oven, I used 2 dinner table chairs to set the oven on, be careful as the front of the oven is heavier than the back. Removed the back sheet metal covers, about 20 screws or so. Removed Fan motor, replaced with new fan motor, and reversed installed. Oven works great.

Changed Fan Blower only, which cleared the Error Code F96.
Other parts have been kept as spares.

Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

TERRIBLE!!!!!!!
FIrst part arrived broken
Second part arrived broken
Third part arrived broken
Finally on the 4th try, the part arrived and was not broken.
I will NEVER again order parts from this company.

Step 1, turn off circuit breaker, verify no power at the back of oven

Step 2, remove oven from wall/housing by removing 4 mounting screws, 2 on each side, just on the inside after opening the oven door...this was the most difficult part doing the repair on my own as the oven is a bit heavy...I was fortunate to have a old Workmate 425 work bench that folds/collapses, this allowed me to slide the oven out and drop down about 2 inches...reinstalling the oven I did have to use 2x4s to shim the oven level to slide it back in, with someone to assist this would not be necessary.

Step 3, remove covers to gain access to the blower and sensor

Step 4, remove the sensor

Step 5, install new sensor

Step 6, turn on the circuit breaker

Step 7, test the oven (success, Y, turn off breaker and reassemble all covers, install the oven, secure with the 4 mounting screws, turn on circuit breaker, test one more to ensure of proper operation...N, go to step 8

Step 8, turn off circuit breaker, reinstall original sensor

Step 9, remove blower

Step 10, install new blower

Step 11, turn on circuit breaker

Step 12, test oven, problem resolved, Y, go to step 13, N, continue troubleshooting.

Step 13, turn off circuit breaker

Step 14, replace all covers and reinstall oven, secure with 4 mounting screws

Step 15, turn on circuit breaker

Step 16, test, still operating properly Y, receive hugs and kisses from wife, N, do not make eye contact with wife, take dog for a long walk.

taking the oven out of the wall the most difficult part.. once you removing the sheet metal screws....be sure to take pictures as you dis-assemble putting back together will be easier. wait for correct part. second try they sent the correct part. put back together, test before putting back into wall.. big savings by doing it yourself.

there was one screw holding it on the back wall of the oven. It was easy enough that my daughter installed it with my guidance.

replaced lights in refrigirator and freezer

I used a Trox bit to remove one screw, replaced the oven sensor and reinstalled the screw. The whole project took less than 5 minutes.