PCT7050DF1WW General Electric Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from PALM COAST, FL
- Parts Used:
- WB25T10102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A burnt out bulb
After opening the Oven door, I removed the glass cover to view and locate the bulb, at the inside, top front of the Oven. Removed the burnt out bulb by pulling it in a forward motion towards the front of the Oven, slid the new bulb into place and the Oven is again functional.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from HASLET, TX
- Parts Used:
- WB21X10165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven was burning when cooking at same temperature we always cooked it on
there was one screw holding it on the back wall of the oven. It was easy enough that my daughter installed it with my guidance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Bremerton, WA
- Parts Used:
- WB21X10165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven would not hold an even temperature.
I used a Trox bit to remove one screw, replaced the oven sensor and reinstalled the screw. The whole project took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from RICHMOND, TX
- Parts Used:
- WB25X20199
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven light falied
This item was listed as fitting my GE wall oven. On arrival it appeared to be the exact part I needed. However upon my attempt to install it I found that the attached male electrical connector was very slightly different from the original part and it would not fit the female connector. At first I thought perhaps I could make a slight modification to the male connector but soon realized that the changes needed were too difficult to make. I tried to locate a matching female connector but no luck. Therefore I decided to use a terminal disconnect tool to unlock the wires from the connector and then I re-used my old connector. It worked! My wall oven is now operational again and my wife is very happy!
P.S., I have been very happy with Parts Select for the availability of old parts and their superb instructional videos. They have helped me make several appliance repairs and are now my first choice
P.S., I have been very happy with Parts Select for the availability of old parts and their superb instructional videos. They have helped me make several appliance repairs and are now my first choice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from MEXICO, NY
- Parts Used:
- WB27T11463, WB26T10066
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
F96 failure code soon after oven is turned on
Removed the top and back covers using a nut driver. Removed fan which is on top of the unit. Installed fan sensor board on new fan using torx bit (board can also be swapped from the old fan if you feel this isn't part of the problem). Installed new fan into oven and replaced the covers.
I built a small table out of scrap wood I had making it the same height as the bottom of the oven in order to make it easy to slide out/in and then work on it. If I didn't do this it would have to be a two person job because the oven is heavy.
I built a small table out of scrap wood I had making it the same height as the bottom of the oven in order to make it easy to slide out/in and then work on it. If I didn't do this it would have to be a two person job because the oven is heavy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from FAIRFIELD, OH
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven meat probe broken
This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.
- works great. tested it....snaps in, reads correctly, snaps out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SOUTHBURY, CT
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Temp probe was defective
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Salih Hindas / from SPRNGFLD GDNS, NY
- Parts Used:
- WB21X10165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Went well.
Changed the Temperature Sensor as you suggested, but the problem of 40 minutes to reach a temperature of 375 degrees F. remained the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from MENIFEE, CA
- Parts Used:
- WB25T10102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burnt out lamp bulb
Remove oven light lens cover, remove the bulb and replace it with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tucson, AZ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Probe Sensor
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Munt Laurel, NJ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Probe broke
Ordered new probe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John R from Asheville, NC
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing meat thermistor
plug in thermistor when needed
Was this instruction helpful to you?
Thank you for voting!