JTP14WT1WW General Electric Wall Oven - Instructions

Per the instructions included with part.

I took the door off, removed the four phillips screws that held the wall oven in it's hole. All the 1/4" fasteners were on the face of the over but you have to pull the oven forward to remove the hinges.
Buying thes two hinges from G.E. would have cost $ 90.00 I paid $ 55.00 from Part Select and they arrived the NEXT DAY. I did not do rush shipping.

One hinge assembly wouldn't close all the way, so the door wouldn't close completely. Removed the door. Removed the screws holding the entire oven to the cabinet (6-8 screws) and pulled out the whole oven about 6 inches. Since it's big and heavy, I rested it on an old plastic milk crate.

The pulley inside one hinge assembly was broken. It's held in by two screws from the front, removed those, took out the old assembly, put in the new, put the screws back in, pushed the whole oven back into the cabinet, put the screws back in to hold it to the cabinet, and put the door back on.

The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)

Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two hex head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.

Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.

Above all else it is imperative that the circuit breaker to the oven be turned off so that no current is flowing to the appliance. Two screws at the base of the heating element need to be removed at which point you can simply pull the element out. Carefully pull the electrical connections off and remove the broken heating element and replace it with the new one. Reinstall the screws. Turn the power back on and allow the element to heat until the oil that was applied to it at the factory burns away as a vapor in a few minutes. You're done!!!

Removed oven from cabinet. unblug old sensor pluged in new and reinstalled oven. Esay repair though wish oven was designed so did not have to pull itout of cabinet which requires disconect electric cabel

I downloaded the installaion manual from the web for this model. First htings first, I located the circuit breaker for the oven and turned it off. Removed the lower trim piece from the bottom, next lifted the oven door off its hinges and set it to the side. I then wrapped a couple of small towels around the hinges for the door as per the manual (the hinges can pinch a finger). I then removed the four screws which secured the oven into the cabinet. Next I slid the oven forward allowing me access to the rear. I removed the pieces from the rear to gain access to the sensors connector, and unpl;ugged the sensor. Went around to the front and unscrewed the 2 screws securing the sensor and removed it. I then installed the new sensor, replaced the rear covers, slid the oven back into the cabinet, secured the four screws, snapped on the lower trim, remounted the oven door, and turned the breaker on. Oven working fine now.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

Took off oven door and removed racks. Removed the cover on the back side (5 screws removed with nut driver) Pulled sensor out the front side of the oven. Threaded the new sensor through and put all back together.

Removed the oven door. Removed screws on side strips and on oven frame where springs were located. Pulled out oven so I could reach the springs. Removed old springs and installed new springs. Installed side strips and remaining screws. Pushed oven back in place and put the door back on.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

I gently pulled the door gasket up at hold pin points - which were spaced every 3-4 inches apart- the pins hold the gasket to the oven door. Once removed, I pushed the pins of the new gasket in holes of the door - starting at top center of door- until all pins were snapped in place. At the bottom of the door are two slotted holes through which each end of the door gasket terminates. Push ends of gasket into these holes until gasket lies flat to oven door.

I remove four screws two on the left side and two screws on the right side. I pull the oven out about ten inches, removed two screws that hold the hinge in place, took out the broken hinge and reverse the installation.

Replaced old with new.

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!