Models
>
JVM6172DK6BB
JVM6172DK6BB General Electric Wall Oven
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JVM6172DK6BB
Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Mar 30
$36.42
The stirrer fan cover in your microwave can be found on the roof of the microwave. It protects the fan from damage and debris. This fan cover is made of white plastic and is approximately 7.5 inches i...
In Stock
Order now and your part arrives by Mar 30
In Stock
Order now and your part arrives by Mar 30
$15.26
This is the replacement damper bracket for your microwave. It is made of plastic and is approximately 11 inches wide and 3 inches long. The damper bracket attaches to the outer cabinet and directs air...
In Stock
Order now and your part arrives by Mar 30
In Stock
Order now and your part arrives by Mar 30
$24.00
This mounting plate, also known as a bracket, is crucial for keeping your microwave mounted to the wall, when placed above the stove. This OEM part is sold separately from the screws that are needed t...
In Stock
Order now and your part arrives by Mar 30
$15.26
This part is the replacement high-voltage diode for your microwave. It is approximately 3 inches long and is sold individually. The high voltage diode is an electrical current control device inside yo...
In Stock
Order now and your part arrives by Mar 30
$37.49
This switch monitor interlock helps your microwave detect when the door is properly closed. If it’s damaged, the microwave may not start. Replacing it restores safe operation and is a quick fix with basic tools.
In Stock
Order now and your part arrives by Mar 30
$16.35
Keep your microwave working safely and efficiently with this aluminum mesh grease filter. Sized at 7.5 by 5 inches, it fits into the underside of your microwave, right above the cooktop, and helps tra...
In Stock
Order now and your part arrives by Mar 30
In Stock
Order now and your part arrives by Mar 30
$21.82
This microwave vent damper assembly helps control airflow by directing exhaust out of the kitchen and preventing outside air, smoke, or odors from flowing back in when the fan is off. Made from durabl...
In Stock
Order now and your part arrives by Mar 30
$24.00
This fan blade, also known as a stirrer blade, is a genuine OEM replacement part for your microwave. This is a fairly easy repair. To complete it, you will need a screwdriver to disassemble the fan as...
In Stock
Order now and your part arrives by Mar 30
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JVM6172DK6BB
Viewing 5 of 5No heat
Fixed by these parts
How to fix it
Won’t turn on
Fixed by these parts
How to fix it
Door not closing properly
Fixed by these parts
How to fix it
Doesn’t shut off
Fixed by these parts
How to fix it
Tray won’t turn
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gregg from Santa Ana, CA
- Parts Used:
- WB27X35382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave made loud buzz noise and did not heat
I followed the generic trouble shooting directions on the web site. It suggested either diode, capacitor and/or magnetron. I test each. All tested OK except diode. It was supposed to measure open in one direction and appox 200k ohms in the other direction. My diode measured open in both directions (tried multiple times, multiple sett
... Read more
ings). I replaced the diode. The order process was great and it shipped immediately. I knew I was in trouble when I measured the new diode and it too was open in both directions. It was easy to install but unfortunately no joy - did not solve the problem. At this point it is likely cheaper just to buy a new one
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michelle from virginia beach, VA
- Parts Used:
- WB20X10048
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Original part was fried
Had to remove microwave from the wall. Then disassemble entire top assembly to get to the part. Easy enough to replace after that. Then just reassemble and reinstall. About 2hrs. total
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Gardiner, ME
- Parts Used:
- WB20X10048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
All power out. No display, not operational
Remove microwave and set on flat surface. Remove all screws on top. Remove all screws around back edge holding top on. Finally remove the screws on botton holding top on and remove top. On left side on top, remove 6 screws holding black channel in place. Also remove 3 screws holding metal top in place. Now lift black channel up and u
... Read more
nplug 2 wires on cutout. Replace cutout and reinstall everything in reverse order. Worst part is taking microwave down and reinstalling.
Read less
Was this instruction helpful to you?
Thank you for voting!