Models
>
E30EW85GSS3
E30EW85GSS3 Electrolux Wall Oven
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for E30EW85GSS3
Viewing 7 of 7Manuals & Guides for E30EW85GSS3
Click to downloadInstall
Installation Instructions
(6.01MB)
Manual
Owner's Manuals
(25.45MB)
Manual
Owner's Manuals
(36.38MB)
Specs
Product Specifications Sheet
(0.38MB)
Wiring
Wiring Diagram
(0.5MB)
Keep searches simple, eg. "belt" or "pump".
$50.31
This is a temperature sensor for a range. The sensor is what detects the temperature inside the oven and is often replaced when the oven is having heating issues. Please note that the wire connector m...
In Stock
Order within the next 17 mins and your part ships today!
In Stock
Order within the next 17 mins and your part ships today!
In Stock
Order within the next 17 mins and your part ships today!
In Stock
Order within the next 17 mins and your part ships today!
In Stock
Order within the next 17 mins and your part ships today!
$160.62
This motor includeds the bracket and the fan retainer nut. Fan blade is sold separately.
In Stock
Order within the next 17 mins and your part ships today!
In Stock
Order within the next 17 mins and your part ships today!
In Stock
Order within the next 17 mins and your part ships today!
In Stock
Order within the next 17 mins and your part ships today!
On Order
In Stock
Order within the next 17 mins and your part ships today!
In Stock
Order within the next 17 mins and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for E30EW85GSS3
Viewing 5 of 5Little to no heat when baking
Fixed by these parts
How to fix it
Oven is too hot
Fixed by these parts
How to fix it
Oven not heating evenly
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from Bellevue, ID
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven not heating to desired temperature
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven
... Read more
and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Stevensville, MD
- Parts Used:
- 318398302
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
replacing the fan on a convection oven (fan was making a vibration noise)
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. O
... Read more
nce there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from RAINBOW CITY, AL
- Parts Used:
- 316217002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not maintain correct set temperature.
Removed electrical connector and two screws. Attached the electrical connector to the new probe and attached with the two screws.
Was this instruction helpful to you?
Thank you for voting!