Models
>
HBL57M52UC
HBL57M52UC (01) Bosch Wall Oven
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for HBL57M52UC
Viewing 12 of 12Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for HBL57M52UC
Viewing 2 of 2Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nancy from ST AUGUSTINE, FL
- Parts Used:
- 00617090
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave was sparking
Replaced the wave cover. Unscrewed existing cover that is at the top inside the microwave. Screwed in the new cover.
Took about 30 seconds to do. Bosch service wanted over $100 for a service call plus parts and labor. Did it myself in seconds for under $10.
Took about 30 seconds to do. Bosch service wanted over $100 for a service call plus parts and labor. Did it myself in seconds for under $10.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ludovic from MIAMI BEACH, FL
- Parts Used:
- 00791650
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Need to replace bake element
First, cut the power and remove the oven from the cabinet.
The bake element is accessible from the back and sits in a drawer.
As someone else said, you have to use pliers to bend the cover of the drawer, you will make some damage to the cover, but there is nothing you can do about it.
Make a note of what w ... Read more ire goes to the right and to the left so you can plug them back like it was before.
When you replace the bake element, make sure you insert it in the straps so it won't wiggle when it heats.
To close the cover that you bent, you will need a helper and push really hard.
The bake element is accessible from the back and sits in a drawer.
As someone else said, you have to use pliers to bend the cover of the drawer, you will make some damage to the cover, but there is nothing you can do about it.
Make a note of what w ... Read more ire goes to the right and to the left so you can plug them back like it was before.
When you replace the bake element, make sure you insert it in the straps so it won't wiggle when it heats.
To close the cover that you bent, you will need a helper and push really hard.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from FREDERICKSBRG, TX
- Parts Used:
- 00772645
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Temperature settings stenciled on the Facia were damaged.
Replace facia panel. Turn off power to the oven. Remove oven control knobs by inserting finger tips under each side of the knob and pulling. Open oven, remove mounting screws. slide the oven out a few inches to allow clearance for the removal of the facia panel. Remove 3 torx screws under the bottom of the facia panel. The wiring harness
... Read more
es for the LED temperature display and touchscreen are very short and must be disconnected in order to remove the facia. Slowly pull out the bottom of the facia panel taking care not to damage the wiring harnesses. Locate the wiring harness connections and disconnect. Lift the facia panel up and away from the oven. Carefully remove the LED temperature display from the back of the facia panel touch screen. Installing the new facia panel: The LED temp display wiring harness is very short and difficult to connect with the LED display installed on the new facia touchscreen panel. For this reason connect the wiring harness to the LED temp display before installing it in the new facia. Once the wiring harness is connected to the LED display, place the facia panel in position and reach under, align the LED display with the touch screen panel mounts and snap into place. Connect the touchscreen harness, position the facia panel and replace the three screws. Secure the oven in place, replace the knobs, and turn on the power.
Read less
Was this instruction helpful to you?
Thank you for voting!