Models
>
020295-0
020295-0 Troy-Bilt Pressure Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 020295-0
Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
$27.80
This fuel valve with bushing fits a variety of outdoor equipment and allows the fuel to smoothly flow into the gas engine. The bushing part is pressed into the hole provided in the fuel tank and the f...
In Stock
Order now and your part arrives by Apr 6
$59.30
This is an original part from Briggs and Stratton, Troy-Bilt, and Snapper for use with Pressure Washers. The outlet tube kit includes the O-ring. The pressure hose connects to the outlet tube, which t...
In Stock
Order now and your part arrives by Apr 6
$122.93
It is a genuine OEM sourced item that is designed for Briggs and Stratton, Snapper and Troy-Built pressure washers. The manifold housing is an important component that attaches to the pump head. It ho...
In Stock
Order now and your part arrives by Apr 6
$23.01
This is a genuine OEM replacement part sourced directly from Craftsman. The thermal relief valve regulates the amount of pressure in the line at any given time. Once the pressure in the line reaches ...
In Stock
Order now and your part arrives by Apr 6
Genuine OEM replacement part, this item is sold in a kit. This is the part of the pressure sprayer that threads into the pump(First in, Spring then the Ball). The the chemical hose kit connects to it....
No Longer Available
$440.38
This is an authentic Craftsman replacement part. The pump assembly is commonly found in pressure washers. This is a complete assembly, including a relief valve, key, and attachment hose. This part ...
In Stock
Order now and your part arrives by Apr 6
In Stock
Order now and your part arrives by Apr 6
$8.25
This is a genuine item that is supplied directly from the original equipment manufacturer for use with Troy-Bilt and Briggs and Stratton pressure washers. It is an identical replacement for a missing ...
In Stock
Order now and your part arrives by Apr 6
$23.29
This manufacturer-approved oil is commonly used in pressure washers. It is made to lubricate the internal pump drive components. This plastic bottle contains 5.3 fluid ounces of oil. It is recommended...
In Stock
Order now and your part arrives by Apr 6
In Stock
Order now and your part arrives by Apr 6
$54.96
This kit has been OEM sourced and is intended to be used with pressure washers from Troy-Bilt and Briggs & Stratton. Check valves can become damaged from air entering the inlet or from chemical residu...
Special Order
In Stock
Order now and your part arrives by Apr 6
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 020295-0
Viewing 2 of 2
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from PICAYUNE, MS
- Parts Used:
- 192980GS
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from RADFORD, VA
- Parts Used:
- 192980GS
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from LEES SUMMIT, MO
- Parts Used:
- 192980GS
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Was this instruction helpful to you?
Thank you for voting!