Models
>
W25SBK
W25SBK Weed Eater Trimmer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for W25SBK
Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
$23.17
This genuine fuel tank assembly is an original replacement part sourced directly from the manufacturer and is commonly used in Craftsman trimmers and weedwackers. Made from high-quality plastic for du...
Special Order
$10.46
This is an authentic Craftsman replacement part that has been sourced from the original manufacturer for use with trimmers. The durable plastic cover is used to house and protect the cutting head's sp...
Special Order
$7.99
Genuine Weed Eater replacement part, this item is sold individually. The 530058000 Trigger is inside the handle of the trimmers shown below. It connects to the throttle cable which controls the speed ...
Special Order
$7.46
This is an Original Manufacturer Approved replacement part. This part is made out of Foam and it is sold individually. The purpose of the filter is to keep dust and debris from contaminating the carbu...
In Stock
Order now and your part arrives by Mar 26
$8.96
This is a genuine Craftsman part for use with Trimmers. The line tap knob releases the cutting line when you bump the knob on the ground while the spool is turning. The most common reason for replacin...
In Stock
Order now and your part arrives by Mar 26
$6.25
This is an authentic OEM sourced replacement piston ring used on gas Trimmers and blowers. A worn or broken piston ring will allow combustion gases to escape the seal and enter the crankcase, causing...
In Stock
Order now and your part arrives by Mar 26
$13.78
This is a Manufacturer Approved replacement kit used on a variety of Gas Trimmers/Pruners. This gasket set includes the major gaskets to replace when rebuilding the engine. Its purpose is to make an a...
Special Order
$14.92
This is a genuine OEM approved replacement starter spring is specially designed for use with gandheld gas powered blowers and trimmers. The purpose of this spring is to retract the starter assembly on...
In Stock
Order now and your part arrives by Mar 26
$36.05
This ignition module is a genuine OEM sourced item, it is not an aftermarket imitation. Ignition module supplies electric current to the spark plug. If the ignition coil is defective, the engine may n...
In Stock
Order now and your part arrives by Mar 26
$38.02
This is an original replacement part manufactured for use with handheld leaf blowers. The flywheel has magnets on its side that create an electric charge as the magnets pass the ignition module. The e...
In Stock
Order now and your part arrives by Mar 26
This item is an authentic replacement part that is sourced from the original manufacturer. The screw is intended to be used with trimmers, blowers, and edgers from Poulan, Weed Eater, Husqvarna, and J...
In Stock
Order now and your part arrives by Mar 26
$10.32
This replacement air box cover is a genuine OEM item, it is not an aftermarket imitation. It is specially designed for Poulan and Weed Eater gas powered trimmers. The purpose of this cover is to secur...
In Stock
Order now and your part arrives by Mar 26
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for W25SBK
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rosanne from BRIDGEWATER, VA
- Parts Used:
- 545227901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Clogged muffler
Remove the 4 screws holding the rear motor casing. Then you can take the easy route and drill through the front motor housing with a 3/8 to 1/2 bit in order to access the front muffler screw. If you want to work harder you must remove the motor from the shaft, remove the clutch assembly (this requires a long 15t torx bit, removing the spa
... Read more
rk plug to stuff the piston with rope or rag to seize up the piston, and then removing the front motor casing to access the front muffler screw). Once you access both muffler screws remove them with the t20 torx driver. Install the new muffler with the small gasket inside the housing, and the larger gasket/heat shield between the muffler and the motor.
Read less
Was this instruction helpful to you?
Thank you for voting!