Models
>
KUCS02FRSS0
KUCS02FRSS0 KitchenAid Trash Compactor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for KUCS02FRSS0
Viewing 6 of 6
Manuals & Guides for KUCS02FRSS0
Click to downloadKeep searches simple, eg. "belt" or "pump".
In Stock
$99.27
This kit contains the normally closed switch, toe guard, template, 2 screws and actuator.
NOTE: This part has been redesigned by the manufacturer but will still function the same as the original part.
In Stock
$49.23
This is a genuine OEM drive gear kit for your trash compactor. It includes the drive gear, pin spring, a retaining clip which is also known as a c-ring, ram stop, and the ram cam. The ram is used to c...
In Stock
In Stock
$8.00
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
In Stock
In Stock
This trash compactor bag carrier with easy grip handles is 15 inches in length. The carrier makes it easy to retrieve full bags of trash from your specific appliance. This is a reusable carrier. When ...
In Stock
$64.14
This is an OEM part sourced directly from the manufacturer. This is a top limit and directional switch that is designed for use with trash compactors. This switch will interrupt the current that flows...
In Stock
Plastic compactor bags. 50% post-consumer recycled plastic 3 millimeters thick to protect from tearing. Slip-N-Grip design prevents the bag from slipping into the compactor. Fits 15" rectangular compactors.
In Stock
In Stock
$16.40
This is a genuine OEM replacement part. This bearing roller is commonly used in the assembly of trash compactors, it allows you to easily slide the container out of the appliance. If the drawer become...
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for KUCS02FRSS0
Viewing 6 of 6Compactor ram gets stuck
Fixed by these parts
How to fix it
Doesn’t stop at end of compacting cycle
Fixed by these parts
How to fix it
Won’t start
Fixed by these parts
How to fix it
Drawer is hard to open and or close
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Won’t stay on
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Ventura, CA
- Parts Used:
- W10342596
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Beware the "two screws, five minutes" repair stories!
Needed a replacement actuator for KitchenAid trash compactor model KUCS03FTSS0. The part that broke is a small metal flange held in place by two screws. PartSelect.com clearly shows this part in the online exploded view of Container Parts. When I received the replacement order in the mail, I was surprised that it was not what I thought
... Read more
I had ordered (a single replacement piece), but a new, *completely redesigned* actuator kit. For this model (and perhaps for other models) this new kit requires much more extensive work than just replacing two screws. Repair entailed removing the trash compactor from its installation position, removing the recess cover and machine front, disconnecting and removing the old actuator switch, drilling holes in the machine front, attaching the new actuator assembly, and disconnecting and reattaching the foot pedal. Not an overly burdensome or complicated repair, but I had been fooled by the expectation of it being a five-minute job! (Submitted on 7/2/2011 by Scott - Ventura, CA)
Read less
Was this instruction helpful to you?
Thank you for voting!
Compactor stuck in lower position
Moved the compactor out from under cabinet and unplugged the powercable.Laid compactor over on its side Removed the top (4 screws) and base plate (3 screws) as well as the coverplate for the motor(3 screws)Found that large drive was broken in half. Used two screwdrivers to start split ring then pliers to pull it off the rest of the way.
... Read more
r />Removed the drive gear and the washer.
Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked.
Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Indianapolis, IN
- Parts Used:
- WP777811
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Trash Compactor ram wouldn't lower
I pulled the trash compactor out from under the counter.
I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical ... Read more directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where.
I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical ... Read more directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where.
Read less
Was this instruction helpful to you?
Thank you for voting!