Models
>
KCC150
KCC150 KitchenAid Trash Compactor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for KCC150
Viewing 10 of 10
Keep searches simple, eg. "belt" or "pump".
$64.14
This is an OEM part sourced directly from the manufacturer. This is a top limit and directional switch that is designed for use with trash compactors. This switch will interrupt the current that flows...
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for KCC150
Viewing 4 of 4Doesn’t stop at end of compacting cycle
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Compactor ram gets stuck
Fixed by these parts
How to fix it
Won’t start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Indianapolis, IN
- Parts Used:
- WP777811
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Trash Compactor ram wouldn't lower
I pulled the trash compactor out from under the counter.
I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical ... Read more directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where.
I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical ... Read more directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Keller, TX
- Parts Used:
- WP777811
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Compactor motor kept running after cycle ran, making alot of noise and unit jumping around.
Pulled the Compactor from underneath cabinet, unplugged power. Removed the top plate off compactor to expose the crush piston. Removed the front control panel by removing two phillips screws, wiring and directional (limit) switch is now exposed. Removed the two screws securing switch, removed wiring one wire at a time and replaced on new
... Read more
switch in same position. Replaced switch in same manner as removed, and followed reverse of above to re-assemble. Plugged back in and tested, problem resolved works like new. Only took possibly 30" to repair and saved an expensive service call.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from El Paso, TX
- Parts Used:
- 776594
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old Plastic Compactor Key Became Brittle and Broke
Original key part number was 776586 as found underneath the the rim of the broken key. It's known as a compactor key, or a key-knob, but in layman's terms, I would call it the "off-on-start" knob. The replacement part number was 386676, and fits perfectly.
The original key had become old and brittle, and eventually just broke a ... Read more part. This was a 30+ year old Whirlpool Trash Compactor key. I just picked out the bits of the old broken key with needle-nose pliers and then easily inserted the new key into the opening.
Note, this literally works just like a key you would insert into any lock. It doesn't require pushing to "snap" into place, but once inserted and turned to the "ON" position, locks into place. No forcing is required at all.
The new key looks exactly like the original and is working very smoothly.
The original key had become old and brittle, and eventually just broke a ... Read more part. This was a 30+ year old Whirlpool Trash Compactor key. I just picked out the bits of the old broken key with needle-nose pliers and then easily inserted the new key into the opening.
Note, this literally works just like a key you would insert into any lock. It doesn't require pushing to "snap" into place, but once inserted and turned to the "ON" position, locks into place. No forcing is required at all.
The new key looks exactly like the original and is working very smoothly.
Read less
Was this instruction helpful to you?
Thank you for voting!