Models
>
BL425-21AK125G965
BL425-21AK125G965 Bolens Tiller
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$35.86
It is an authentic manufacturer-sourced replacement part that i supplied for Craftsman trimmers. The function of a carburetor is to mix the air and the gas into a highly combustible mix before it goes...
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
$4.44
This is a TT screw, but it is also called a fastener, and it is used on multiple outdoor tools. This part is a Tri-Round or Tri-Lobular thread forming screw, it is 0.25 inches in diameter, 0.5 inches ...
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
This is a flange lock nut, and it is used with various outdoor tools and equipment. The flange lock nut is all one piece. It has a bottom circular flange and a smaller top hex section. This is a torqu...
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
$10.70
This switch is used on a variety of trimmers, blowers and other similar gardening equipment. This switch controls the on and off operations of your tool. Switches have mechanical internals, which degr...
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for BL425-21AK125G965
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
string trimmer would not start
emptied fuel from tank. pulled off the 2 fuel lines from the carburetor.opened the air cleaner door. removed the 2 torque screws that hold on the carburetor. removed the carburetor and air cleaner gasket. installed new carburetor and gasket and put back and tightened the 2 torque screws. closed air cleaner door and pushed the fuel lines o
... Read more
nto the new carburetor.put some fuel in the tank. started the trimmer. runs great.
Read less
Was this instruction helpful to you?
Thank you for voting!
Carburetor replacement
Removed 2 screws securing the air cleaner and carburetor to the engine using a T25 Torx driver. then removed the throttle cable from the carb.Then removed the o ring gasket from the engine and replaced with a new one and replaced the carb etc. Primed it and fired it up.Runs just like new.
Was this instruction helpful to you?
Thank you for voting!
Trimmer Would Not Start
The replacement of the carburetor, O-ring, and gasket was simple. I removed 2 screws that held the air cleaner and carburetor in place, swapped them out, and replaced the screws. What took longest was finding a piece of fuel line after breaking one of them. It was brittle after hanging in my garage for several years. I found some in my
... Read more
garage and replaced it. It took a few pulls to get it started, but ran very smooth.
Additional information: rather than mixing my fuel, I purchased 40:1 pre-mix fuel to prevent gunking up the carburetor in the future. I use it in my other trimmer and have not had any issues.
Additional information: rather than mixing my fuel, I purchased 40:1 pre-mix fuel to prevent gunking up the carburetor in the future. I use it in my other trimmer and have not had any issues.
Read less
Was this instruction helpful to you?
Thank you for voting!