Models > EA2121WT

EA2121WT Speed Queen Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
V-Style Drive Belt (32.5 inches long) – Part Number: WP28808
$43.27
This v-style drive belt is thirty-two and a half inches long and half of an inch wide.
In Stock
Order within the next 8 hrs and your part ships today!
Complete Hub and Seal Kit – Part Number: R9900552
This kit comes with hub, seal head, gasket, seal shroud, seal seat, screw, spline insert, drive bell and seal.
No Longer Available
V-Style Cogged Pump Belt (22.5 inches long) – Part Number: WP27155
$39.81
This V-style cogged tooth pump belt is used in conjunction with the drive belt in your washing machine. This belt is all black in color and is made entirely of rubber. It is twenty-two and a half inch...
Special Order
Drain Pump - 2 Port – Part Number: 31969
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
No Longer Available
Two Speed Motor – Part Number: 27179P
This two speed motor performs 1725 revolutions per minute in one speed, and 1140 revolutions per minute in the second speed. It runs at 1/2 horsepower and carries 115 volts. You can use this washer mo...
No Longer Available
SNUBBER PA – Part Number: 36108
No Longer Available
TRANSMISSN – Part Number: 34526P
$479.30
Special Order
Idler Pulley Wheel – Part Number: WP28800
This idler pulley wheel is not quite three inches in diameter. It is black and made of plastic with a metal center.
No Longer Available
Timer – Part Number: 31111P
No Longer Available
WIRE HARNESS – Part Number: 207161
No Longer Available
DISCONTINUED – Part Number: 27762
$39.10
Special Order
Hose, Tube & Fitting – Part Number: 33513
Agitator straight short
No Longer Available
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for EA2121WT

Viewing 5 of 5
Leaking
Fixed by these parts
Fixing Fixing
How to fix it
Will not agitate
Fixed by these parts
Fixing
How to fix it
Burning smell
Fixed by these parts
Fixing
How to fix it
Will not drain
Fixed by these parts
Fixing Fixing
How to fix it
Spins slowly
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
John from Milton, PA
Parts Used:
WP28808
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Frayed V-belt
VERY EASY!!!
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, r emove 4 mounting bracket screws that secure the motor and pump assembly. Pull back the tension/idler pulley to loosen belt off the main pulley to the washer drum. Tilt and pull out motor/pump assembly. Underneath the pump, use star-bit to remove the pump from motor assembly to remove the belt. Install new belt on motor pulley (Good time to check for debris or anything restricing free movement of pump) and re-install pump. Install the motor/pump assembly and loosely secure the motor/pump assembly. Place the belt onto the motor pulley and pull back the tensioner/idler pulley to allow slack of belt to be placed on washer drum pulley. Put the belt on the lip of the drum pulley and rotate while pulling back the tensioner/idler pulley until the belt is seated on the groove of the drum pulley. Tighten the motor/pump assembley. Re-attach the 2 hoses and tighten down the clamps. Re-connect the electrical connector to the motor...Don't forget to plug in the washer and secure the front panel...Piece 'O cake, you're done! About 15 minutes to do the job. Much like changing a belt on most vehicles.
Read less
59 of 66 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
HOWARD from CORTLAND, OH
Parts Used:
R9900552
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
The Seal On The Bottom Of The Tub Was Leaking
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty much straight forward. Primed the pump and started the machine for the stated time and was a sucess.
Read less
33 of 42 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Raymond from East Sandwich, MA
Parts Used:
R9900552
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Socket set, Wrench set
tub leaking water
Took off the agitator, removed inner tub, exposing the hub drive. Found fusion between hub drive and agitator shaft. Rather than using a wheel puller as instructions recommended I got my masonry hammer and removed the drive hub in pieces. Removed debris from the tub. Installed sealant around lower seal as instructed. Re-assembled inne r tub, agitator with new upper seal. Plugged in the washer, turned on the water. No leak. Happy happy.
Read less
18 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More