Models > 316E733E401

316E733E401 (1996) Yard Man Snow Blower

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for 316E733E401

Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
This carriage bolt fits a variety of tools and is sold individually. The square area under the head of the bolt is created to fit into a square hole in your tool. The hole makes sure to restrain the b...
In Stock
$22.16
This slide or skid shoe fits snow blowers and is attached to the auger housing. The shoe slides around the ground to ensure the snow blower glides and moves easily. It also elevates the auger housing ...
On Order
In Stock
This is a TT screw, but it is also called a fastener, and it is used on multiple outdoor tools. This part is a Tri-Round or Tri-Lobular thread forming screw, it is 0.25 inches in diameter, 0.5 inches ...
In Stock
This is a plastic bushing for your lawn equipment. It fits onto the side of your fuel tank, and holds the fuel fittings so they do not touch sharp metal. This part is made of plastic, and will eventua...
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
This is a Belleville washer, and it is used with various lawn and garden equipment around your home. This part has an inner diameter of 0.340 inches and an outer diameter of 0.872 inches. The convex s...
In Stock
This lock washer is used to resist the loosening of bolted joints. Repair tip: It is difficult to install the lock washer in a tight place or when the bolt/screw is pointing down. This lock works with...
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Fortney Auto Shop from PISCATAWAY, NJ
Parts Used:
954-0346
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
Worn belts
Removed bottom plate and belt cover and replaced 3 belts
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
LISA M from BATESVILLE, AR
Parts Used:
737-0300A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Mixer began to make a noise on speed two and higher
We took our 30 plus year mixer apart. I removed the old grease. There was some crumbly looking grease in the main housing gear section where the nylon gear is located. It looked like it had flour mixed in it. Not certain. Removed as best possible all old grease and applied 6 oz. of new Benalene grease to all of the gears. Now it do es not make the slight howl sound.
5 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from HARRISVILLE, NH
Parts Used:
790-00121-0637
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set
Original shave plate badly worn
With WD-40 or equivalent, spray the four nuts on the underside of the snow blower housing that hold the shave plate to the housing. Also spray the two bolts that hold the shave plate to the side of the housing. Let sit for a few minutes and using a 1/2" box end wrench remove the four nuts on the bottom of the housing. If necessary, app ly heat with a torch to loosen. Using a 9/16" box end wrench, remove the nuts on the sides (these also hold the adjustable skid feet). It is recommended that the bottom bolts and nuts be replaced with 5/16-18 X 3/4" long zinc plated carriage bolts using zinc plated washers and ny-lock nuts. It is also recommended that all of th screw threads be coated with an anti- seize lubricant so disassembly at a later date will be easy.
4 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!