Models
>
38597
38597 (280000001-280999999) Toro Snow Blower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$30.61
This engine tune-up kit provides the basic maintenance items needed to keep a small engine running smoothly and reliably. It includes commonly replaced service components that support proper lubricati...
Special Order
$5.95
Genuine OEM sourced part used on variety of Toro Lawn and Garden Equipment. This part is sold individually and the Nut is not included. The square area under the head is designed to fit into a square ...
In Stock
Order now and your part arrives by Aug 6
$6.55
This is a lock nut and it is used in a variety of outdoor lawn equipment. This lock nut has a nylon insert, making it a nyloc nut. The insert allows the nut to be resistant to turning caused by strong vibrations.
In Stock
Order now and your part arrives by Aug 6
$6.55
This is a nut, for a variety of outdoor lawn equipment. This part is a nylon insert locking nut, meaning it has a nylon collar insert that makes the nut resistant to turning from heavy vibrations. It ...
In Stock
Order now and your part arrives by Aug 6
$6.51
This is a genuine OEM sourced replacement part designed for use with Toro snow blowers/throwers. This steel washer helps to distribute the pressure evenly and allowing parts to be secured safely. It i...
In Stock
Order now and your part arrives by Aug 6
$6.55
This screw is an OEM part sourced directly from the manufacturer and is used in Toro snowthrowers. It requires a wrench and connects the ring-chute to the chute-discharge. The screw is made of metal a...
In Stock
Order now and your part arrives by Aug 6
$6.55
This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it bec...
In Stock
Order now and your part arrives by Aug 6
This is a screw for your lawn equipment. Most commonly used to secure the half-rotor to the blade in your machine. This part is a hex bolt, and requires a nut or a tapped hole.
In Stock
Order now and your part arrives by Aug 6
$6.55
This is a genuine Toro replacement part that has been sourced from the original manufacturer to be used with snowthrowers. The metal hex head screw is used to secure the impeller assembly. This item i...
In Stock
Order now and your part arrives by Aug 6
$6.51
This screw is an authentic OEM sourced hardware, it is not an aftermarket imitation. It is commonly utilized on Toro snow throwers. It is a standard hardware which has multiple uses depending on your ...
In Stock
Order now and your part arrives by Aug 6
$31.85
The ball bearing fits next to the bearing cup flange. This part is available individually and is a genuine part sourced directly from the manufacturer for use in snowthrowers by Toro and Lawn Boy. It ...
In Stock
Order now and your part arrives by Aug 6
$6.51
This replacement screw is a high quality item commonly utilized on Toro snowthrowers. It is a genuine OEM supplied hardware which has multiple uses depending on the equipment. Please make sure to chec...
In Stock
Order now and your part arrives by Aug 6
$6.55
This is an authentic replacement part manufactured for use with Toro snowthrowers. The ni lock nut is designed to prevent from being unthreaded from vibration. This nut is used with several different ...
In Stock
Order now and your part arrives by Aug 6
Common Problems and Symptoms for 38597
Viewing 2 of 2Will Not Start
Fixed by these parts
How to fix it
Cannot pull starter cord out or engine will not turn over
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dana from HAMMOND, IN
- Parts Used:
- 792006
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Mistreated Briggs & Stratton 206 CC Engine on MTD Chipper
Removed tank and drained old gas.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alberto from PALMETTO BAY, FL
- Parts Used:
- 692237
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Generator would not start, Birggs & Stratton recommended to replase Gasket Exhaust.
Remove the spark suppresser, 4 face screws, 2 bottom screws and the two screws the hold the gasket. I also had to back out the top screw of the cover it blocked and prevented the removal of the gasket.
Was this instruction helpful to you?
Thank you for voting!