Models > 1695875

1695875 Simplicity Snow Blower

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for 1695875

Viewing 9 of 9
Keep searches simple, eg. "belt" or "pump".
This knob is used on a variety of lawn and gardening equipment and acts as a nut to fasten bolts and stayed secure in your tool. Replace this part if your bolt is loose and needs security. The diamete...
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
This hex nut is created for use on lawn and gardening equipment. This is a multi-application nut that depends on the unit and tool you are using. For installation instructions, check the manual provid...
In Stock
Order within the next 11 hrs and your part ships today!
$23.33
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
Questions and Answers

Questions and Answers

Be the first to ask our experts a question about this part!

Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
  • Customer:
    Duane from RICHFIELD, MN
  • Parts Used:
    1687806
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
Scraper bar and flight worn past wear limit.
Removed scraper bar and support. Removed flight paddles. Several retaining screws were seized requiring WD-40 and vice grips for removal. Torx sockets stripped out due to threads being seized. Hex head cap screws would be better for both scraper bar and flight papples.once the screws were removed I used a tap to clean the threads and applied lubricant to minimize future corrosion. Three of the four lock nuts for the scraper bar were either not included or lost in shipping due to poor packing requiring me to purchase replacements.
Overall, the job took longer than it should have due to the additional time required to remove seized screws and acquire replacement lock nuts.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    julianne from CEDAR RAPIDS, IA
  • Parts Used:
    1739338YP
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Socket set, Wrench (Adjustable)
Initially, belt came off, lodged between pulley and housing. When replace, belt broke
NOTES: 1) This is not a new model, but a rebranded version - previously under Murray, Simpliticy, Snapper, etc., so parts are available, but not readily identified yet.
2) This repair may be quite simple or it may be a huge problem, depending on whether the manufacturing problem described below is present.
3) The space between the housing and aluminum pulley is so tight that a belt CANNOT be fit through it!
Therefore, the only way to replace the belt is to remove the pulley.
* * * * * * * * * * * * * * * * * *
Step 1. As with every other single stage snow blower, remove the belt cover held by six 10 mm bolts. This may require a metric nutdriver or a deep socket for a couple of bolts.
Step 2. Use a 17 mm wrench to remove the large nut holding the aluminum impeller pulley, along with the flat and split lock washers. Also remove the part that locks the pulley onto the shaft.
Step 3a. If there is not a manufacturing issue, the pulley will come off easily and you may proceed to thread the new belt around the power and idler pulleys.
Step 3b. IF THE PULLEY DOES NOT COME OFF, you may need to get a wheeler puller tool to get it loose and off the shaft. Once the overly tight pulley is off, you may wish to file down the shaft near the end until the pulley slides on and off without much effort. (You may also wish to apply a dry silicone lubricant to the shaft to make the job easier next time.)
Step 4. In order the install the new belt, feed it around the power pulley and the idler pulley controlled by the "engage" handle. With the impeller pulley still off its shaft, feed the belt around it, fitting the belt grooves into the pulley grooves.
Step 5. The large aluminum can be replaced on its shaft, followed by the pulley lock, flat washer and split ring washer. Tighten the pulley lock nut, holding the impeller blades to keep the shaft from turning.
Step 6. Replace the belt cover and the six bolts holding it in place.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!