Models
>
1696307-01
1696307-01 Murray Snow Blower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$10.50
This knob is used on a variety of lawn and gardening equipment and acts as a nut to fasten bolts and stayed secure in your tool. Replace this part if your bolt is loose and needs security. The diamete...
In Stock
Order now and your part arrives by Mar 20
$10.40
This authentic replacement part is designed for use with Craftsman snowblowers. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distribut...
In Stock
Order now and your part arrives by Mar 20
$6.40
This hex nut is created for use on lawn and gardening equipment. This is a multi-application nut that depends on the unit and tool you are using. For installation instructions, check the manual provid...
In Stock
Order now and your part arrives by Mar 20
This is a genuine OEM supplied replacement drive belt, it is specially manufactured for use with Murray, Snapper and Simplicity snowblowers. This is the belt that helps to drive the augers. Over time ...
No Longer Available
$6.25
It is an authentic manufacturer-approved replacement part which is produced for use with Murray, Snapper and Briggs and Stratton lawn and garden equipment. This special bolt is utilized to secure the ...
In Stock
Order now and your part arrives by Mar 20
This is a genuine manufacturer-approved component which is specially made for use with Murray and Snapper snowthrowers. The purpose of this pulley is to apply tension to the belt. It provides an ident...
No Longer Available
In Stock
Order now and your part arrives by Mar 20
Special Order
In Stock
Order now and your part arrives by Mar 20
This is an OEM part sourced directly from the manufacturer. The nylock nut is commonly found in snow throwers and lawn tractors from Murray and Snapper. This part is made of metal, and may be found ...
In Stock
Order now and your part arrives by Mar 20
It is a genuine OEM sourced part that is specially produced for use with Murray and Snapper lawn and garden equipment. This is a standard hardware which may have multiple applications, please make sur...
Special Order
In Stock
Order now and your part arrives by Mar 20
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- julianne from CEDAR RAPIDS, IA
- Parts Used:
- 1739338YP
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Initially, belt came off, lodged between pulley and housing. When replace, belt broke
NOTES: 1) This is not a new model, but a rebranded version - previously under Murray, Simpliticy, Snapper, etc., so parts are available, but not readily identified yet.
2) This repair may be quite simple or it may be a huge problem, depending on whether the manufacturing problem described below is present.
3) The space between t ... Read more he housing and aluminum pulley is so tight that a belt CANNOT be fit through it!
Therefore, the only way to replace the belt is to remove the pulley.
* * * * * * * * * * * * * * * * * *
Step 1. As with every other single stage snow blower, remove the belt cover held by six 10 mm bolts. This may require a metric nutdriver or a deep socket for a couple of bolts.
Step 2. Use a 17 mm wrench to remove the large nut holding the aluminum impeller pulley, along with the flat and split lock washers. Also remove the part that locks the pulley onto the shaft.
Step 3a. If there is not a manufacturing issue, the pulley will come off easily and you may proceed to thread the new belt around the power and idler pulleys.
Step 3b. IF THE PULLEY DOES NOT COME OFF, you may need to get a wheeler puller tool to get it loose and off the shaft. Once the overly tight pulley is off, you may wish to file down the shaft near the end until the pulley slides on and off without much effort. (You may also wish to apply a dry silicone lubricant to the shaft to make the job easier next time.)
Step 4. In order the install the new belt, feed it around the power pulley and the idler pulley controlled by the "engage" handle. With the impeller pulley still off its shaft, feed the belt around it, fitting the belt grooves into the pulley grooves.
Step 5. The large aluminum can be replaced on its shaft, followed by the pulley lock, flat washer and split ring washer. Tighten the pulley lock nut, holding the impeller blades to keep the shaft from turning.
Step 6. Replace the belt cover and the six bolts holding it in place.
2) This repair may be quite simple or it may be a huge problem, depending on whether the manufacturing problem described below is present.
3) The space between t ... Read more he housing and aluminum pulley is so tight that a belt CANNOT be fit through it!
Therefore, the only way to replace the belt is to remove the pulley.
* * * * * * * * * * * * * * * * * *
Step 1. As with every other single stage snow blower, remove the belt cover held by six 10 mm bolts. This may require a metric nutdriver or a deep socket for a couple of bolts.
Step 2. Use a 17 mm wrench to remove the large nut holding the aluminum impeller pulley, along with the flat and split lock washers. Also remove the part that locks the pulley onto the shaft.
Step 3a. If there is not a manufacturing issue, the pulley will come off easily and you may proceed to thread the new belt around the power and idler pulleys.
Step 3b. IF THE PULLEY DOES NOT COME OFF, you may need to get a wheeler puller tool to get it loose and off the shaft. Once the overly tight pulley is off, you may wish to file down the shaft near the end until the pulley slides on and off without much effort. (You may also wish to apply a dry silicone lubricant to the shaft to make the job easier next time.)
Step 4. In order the install the new belt, feed it around the power pulley and the idler pulley controlled by the "engage" handle. With the impeller pulley still off its shaft, feed the belt around it, fitting the belt grooves into the pulley grooves.
Step 5. The large aluminum can be replaced on its shaft, followed by the pulley lock, flat washer and split ring washer. Tighten the pulley lock nut, holding the impeller blades to keep the shaft from turning.
Step 6. Replace the belt cover and the six bolts holding it in place.
Read less
Was this instruction helpful to you?
Thank you for voting!