Models
>
31AE5D8E099
31AE5D8E099 (2003) MTD Snow Blower
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This carriage bolt fits a variety of tools and is sold individually. The square area under the head of the bolt is created to fit into a square hole in your tool. The hole makes sure to restrain the b...
In Stock
Order now and your part arrives by Apr 30
$37.57
This slide or skid shoe fits snow blowers and is attached to the auger housing. The shoe slides around the ground to ensure the snow blower glides and moves easily. It also elevates the auger housing ...
In Stock
Order now and your part arrives by Apr 30
This replacement shear bolt is supplied directly from the original equipment manufacturer for use with Craftsman snowblowers. The purpose of this hardware is to protect your snowblower. If the auger g...
In Stock
Order now and your part arrives by Apr 30
This is a TT screw, but it is also called a fastener, and it is used on multiple outdoor tools. This part is a Tri-Round or Tri-Lobular thread forming screw, it is 0.25 inches in diameter, 0.5 inches ...
In Stock
Order now and your part arrives by Apr 30
$6.51
This is a plastic bushing for your lawn equipment. It fits onto the side of your fuel tank, and holds the fuel fittings so they do not touch sharp metal. This part is made of plastic, and will eventua...
In Stock
Order now and your part arrives by Apr 30
This is a Genuine OEM replacement Belt set designed for use with Snowblower. This part is made out of Rubber and it includes one belt. This belt drives your unit. Make sure to clean pulleys before i...
In Stock
Order now and your part arrives by Apr 30
On Order
$23.18
This item has been sourced from the original manufacturer to be used with snowblowers from MTD, Ryobi, Yard Machines, Bolens, and Yard-Man. This item is the hard rubber tire that fits onto the frictio...
On Order
$40.52
This is an authentic OEM sourced replacement part designed for use with snow throwers/blowers. It allows you to engage and disengage the unit. This cable is sold individually. You may need pliers to ...
In Stock
Order now and your part arrives by Apr 30
$6.69
This lock washer is used to resist the loosening of bolted joints. Repair tip: It is difficult to install the lock washer in a tight place or when the bolt/screw is pointing down. This lock works with...
In Stock
Order now and your part arrives by Apr 30
On Order
$6.51
The chute flange keeper attaches to the lower chute using the flange lock nut and helps the chute to pivot. This is a genuine replacement part made by Ryobi, MTD, and Yard Machines for use in snow thr...
In Stock
Order now and your part arrives by Apr 30
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 31AE5D8E099
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from MILLSTONE TWP, NJ
- Parts Used:
- 36624
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Bad Camshaft made of plastic
Original engine had camshaft made of plastic. Engine had a seal leak on shaft lost oil . Result was seized bearing and stripped camshaft. Ordered a replacement camshaft and gasket. Gasket came in a week after original due date and camshaft is NOT AVAILABLE. Didn't know that at original order. Followed up twice with operator, not ema
... Read more
il and got a non-answer answer. No idea when part will be available and requested a second contact and update. Same no idea reply. Result is a waste of my time with this company, will NOT use them again.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LISA M from BATESVILLE, AR
- Parts Used:
- 737-0300A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Mixer began to make a noise on speed two and higher
We took our 30 plus year mixer apart. I removed the old grease. There was some crumbly looking grease in the main housing gear section where the nylon gear is located. It looked like it had flour mixed in it. Not certain. Removed as best possible all old grease and applied 6 oz. of new Benalene grease to all of the gears. Now it do
... Read more
es not make the slight howl sound.
Read less
Was this instruction helpful to you?
Thank you for voting!